直射模製 的英文怎麼說
中文拼音 [zhíshèmózhì]
直射模製
英文
straight injection molding-
This thesis firstly introduces new demands of aerial product logistics support under high - tech war and some defects of traditional logistics support, and puts forward a kind of system model of aerial product logistics support following data - sharing of cals, and emphasizes detm. secondly it sets forth application of step and xml in the ietm, researchs conversion of xml schema and relation schema, and simply researchs mapping of xml and express. afterword, a based - xml framework of info - transfer between different platform are presented, according to this framework, the author establish a archetypal system of helicopter information query system based xml and dbms
本文首先介紹了現代高科技戰爭條件下對航空產品維修保障的新要求，概述了傳統的後勤保障技術的不足，遵循cals的數據共享的理念，提出了航空產品維修保障系統模型，重點研究了互動式電子技術手冊；接著分析了step標準和xml技術在製作互動式電子技術手冊中的應用，重點研究了肌模式和關系模式之間的相互轉換，初步研究了xml和express語言之間的映射關系；然後，提出了基於xml的一種解決航空產品信息跨平臺傳遞的解決方案，給出了該方案的具體實現流程和詳細的通訊協議，並開發了基於xul和數據庫的某型號直升飛機的信息查詢原型系統。Of the currently available coolers for electronic products with a high heat flux, micro - jets impingement cooling heat sinks are able to provide the best heat transfer performance : lowering the maxmal temperature and the temperature difference. the heat transfer for multiple jets impingement has been studied firstly for summarizing a few rules. and then a copper micro - jets impingement cooling heat sink consisting of five copper sheets is designed in this paper and the jet diameter is 0. 15mm
本文首先對陣列射流沖擊進行了實驗研究，總結了陣列射流沖擊的一些規律和特性，在此基礎上，根據數值模擬優化結果設計和製作了微射流陣列冷卻熱沉（射流孔直徑d = 0 . 15mm ） ，並採用去離子水和氮氣作為工質，對熱沉內流體壓降和傳熱特性進行了研究。This paper realized frequency modulation using the video signal to directly control the resonance loop ' s diode of the vco at the early stages, and then through using radio frequency bipolar junction transistor, designed a lc voltage controlled oscillator which was emulated by advance design system. in addition, it also implemented the design and debugged the hardware circuit
本文第一次實驗採用視頻信號直接控制vco諧振迴路變容二極體的方式實現頻率調制，並且利用射頻雙極性晶體管（ bjt ）設計了一種lc壓控振蕩器，通過ads軟體進行了參數模擬，最後進行了硬體電路的製作和調試。Because of drastical cost in development, manufacture, launch and on orbit management of the space station system, this is necessary to set up a simulation platform or a virtual prototype instead of its physical system
空間站系統從研製、發射直至運行管理的代價非常昂貴，建立其模擬平臺或虛擬樣機代替其物理樣機進行研究是一個效費比較高的手段。Mould board cabinet - type support base integral strcture, small diameter of screw bar with large length against diameter ratio, full computer dynamping color display temperature tuzzy controlling, imported hydraulic electrical devices, tine mould clamping rigidity, high precidion of injection, it is suitable for injection with engineering plastics
模板箱式支座連體結構，螺桿小直徑、大長徑比，全電腦動態彩色循環顯示，溫度模糊控制，進口液壓電氣配置，整機合模剛性好，注射精度高，適合工程塑料製品注塑成型。分享友人