磨擦聚合物 的英文怎麼說

中文拼音 [mócājùgěwù]
磨擦聚合物 英文
friction polymers
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 聚 : 動詞（聚集; 聚積） assemble; gather; get together
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 物 : 名詞1 （東西） thing; matter; object 2 （指自己以外的人或與己相對的環境） other people; the outsi...
  • 磨擦 : rub; abrade; abrase磨擦電 triboelectricity; 磨擦工 rubber; 磨擦劑 abrasive; 磨擦器 grater; rubber...
  • 聚合物 : [化學] polymer; polymerizate; polymeric compound; polymeric substance; polymeride; polymerized su...
  • 聚合 : 1 （聚集到一起） get together2 [化學] （單體結合成高分子化合物） polymerization; polymerize 3 [生...
  1. The variation of friction coefficients of pa6 composites with loading also accords with the friction behaviors of elastic materials under lower load ( p < 100 n ) ; for cu counterface, the friction coefficients of pa6 composites increase with the increasing of filler contents at the same load

    我們認為，聚合物材料的摩擦系數變化除了與材料本身性能有關外，還與摩擦副的硬度有關。納米al _ 2o _ 3的加入，尼龍6的磨損量下降，但是對于尼龍6而言，存在一個最浙江
  2. The progress in the research on the mechanical properties, mechanism of tribological wear, biological compatibility and microstructure of carbon fiber ( cf ) reinforced polyether - ether - ketone ( peek ) composite is reviewed in this paper

    摘要綜述了碳纖維增強聚醚醚酮（ peek ）復合材料在機械力學性能、摩擦磨損機理、生物相容性、微觀結構等方面的研究進展。
  3. ( 2 ) it is found that distilled water as lubricant can markedly reduce the accumulation of friction heat and temperature rise on the frictional surfaces of polymer. so the heat fatigue and adhesive wear decrease. moreover, a lubricating film forms on the interface between the counterpart and polymer when distilled water acts as polar lubricant

    （ 2 ）潤滑劑水的存在，可大幅度降低聚合物磨損表面的摩擦熱積累及溫升，從而減少了基體的熱疲勞磨損和粘著磨損，同時，水作為一種極性潤滑劑，在摩擦界面上能形成一層潤滑膜，對摩擦表面起了一定的隔離作用。
  4. In this paper, the microstructure changes of polypropylene induced by a complex combination of shearing, compression, stretching and friction actions during single pan - milling or co - milling with iron, uhmwpe and waste tire rubber chips ( wtr ) were studied and the stress induced effects were revealed. the structure and morphological development of iron particulates and wtr during pan - milling and co - milling with polypropylene were also characterized. the properties of pp / fe, pp / wtr and pp / wtr / fe composites prepared through pan - milling techniques were investigated

    本文利用磨盤型力化學反應器對被碾磨材料施加強大的剪切、環向應力、擠壓、拉伸和摩擦作用，研究聚丙烯碾磨和共碾磨粉碎過程微觀形態結構和性能的變化，以及聚合物在碾磨過程中呈現的力化學現象，並將其應用拓展至金屬、橡膠等體系，研究碾磨粉碎在聚丙烯鐵超微粉體的制備、高交聯密度彈性材料廢舊輪胎橡膠（ wtr ）的超微粉碎，以及pp fe ， pp wtr材料的性能與碾磨作用的關系。
  5. The process and mechanisms of slipping, exfoliation to layered graphite and compounding with polypropylene ( pp ) on nano - scale were systemically studied. the effects of shearing force field offered by pan - milling and confined environment of the exfoliated graphite on the microstructure of polypropylene, the electrical and thermal conductivities of the nanocomposites were also investigated. based on the experimental results, a modified electrical conductive model as well as thermal conductive model for polymer - based composites was proposed

    利用層狀無機物（如石墨）的弱層間結構和聚合物的粘彈性特點，在磨盤碾磨剪切力場作用下，通過摩擦和拉伸形變錯位、擠壓嵌合、拉伸滑移、剪切剝離與粉碎和混合分散等過程，實現層狀無機物層間剝離和與聚合物的納米復合。
  6. The major conclusions of this thesis are listed as follows : ( 1 ) the influence of sliding velocity on polymers " tribological behaviors concerns mainly with the effect of friction heat

    獲得了以下主要結論： （ 1 ）滑動速度對聚合物材料摩擦磨損性能的影響主要與摩擦界面的熱效應有關。
  7. Instructions : bg006, used special polymer made by rohm haass, can be maintained by using 2500rpm high speed polisher. it has the characters of high gloss, water proof, and anti - friction

    產品說明：能使用超高速拋光機進行維護的使用羅門哈斯特殊聚合物的高性能蠟。在2500rpm的高轉速下該蠟可以顯示出其優異的光澤，防水耐磨抗刮擦性能！
分享友人
分享到 Line

分享到臉書