移軸補償 的英文怎麼說

中文拼音 [yízhóubǔcháng]
移軸補償 英文
axial balance
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. This paper introduces one novel protected clutch, which is simple in construction, good in usability, low for cost and movement expenditure, long for working life, rapid for jont or separation, compensable for all kinds of offset, and protected for overload

    摘要介紹一種結構簡單、工藝性好，造價、運行費用低廉，壽命長，可在運動中迅速接合分離，可補償兩軸之間的任何偏移，能過載安全保護的新型安全離合器的結構設計。
  2. Cross universal coupling is mainly used for rolling machine, mining machine, transportation machine, petroleum, shipping, making paper and other heavy - duty machine, is the most common and highest efficiency gearing, it has larger transmit moment, bigger angle, more flexible rotation, longer life than the old - type plum blossom shaft, smooth piece universal shaft, and gear coupling, it s a new generation product of changing the metallurgy steel rolling equipment reconstructive technology

    利用其結構的特點能使不在同一軸線或軸線折角較大或軸向移動較大的兩軸等角速連續回轉，並可靠地傳遞轉矩和運動。其最大的特點是各向位移補償能力強，結構緊湊，傳動效率高，維修保養方便。廣泛應用於冶金機械，石油機械，造紙機械，工程機械，起重運輸機械以及其他重型機械等等。
  3. The three major types of machining error are geometric, thermal and cutting - force induced error. at the present time, error compensation model usually aims at single type of error and is used for the specific machine tool. this paper develops a universal synthetical model of error compensation for three - axis numerical control ( nc ) machine tool, which can be updated on time when manufacturing surroundings is changed

    論文廣泛研究了機床誤差補償技術目前的發展狀況，針對目前誤差補償系統存在的不足（諸如大多為單項誤差補償、通用性較差，模型多為靜態等） ，提出了機床綜合誤差的補償策略，以三軸數控機床為例建立了綜合誤差補償系摘要統，系統的誤差模型可實時更新，該補償系統可直接移植到多軸加工系統中。
  4. Traditional inertial mechanized - platform uses velocities to damp the system attitude to improve the precision of attitude, when the system acceleration is small. referring to the idea, this paper designeda damp kalman filter in strap - down attitude heading reference system ( ahrs ). the new method makes use of 3 - d accelerometer ' s measurements to estimate the system attitude, which is measured to compensate attitude errors. because the acceleration affected the precision of fiher directly, the fuzzy adaptive system was presented. the fuzzy logic inputs are three accelerations and the output is to control the measurement noise covariance matrix. simulations and experimental results prove that the damp algorithm can damp most of schuler oscillation and foucauh oscillation, so that to assure the filter convergence and efficiently improve the precision of strap - down ahrs

    在系統機動性不強的情況下，傳統的平臺內阻尼演算法將系統本身的速度信息通過阻尼網路加到系統中，達到提高姿態角精度的目的.將這種平臺內阻尼的思想引入到捷聯慣性航姿系統中，在系統加速度較小的情況下，利用加速度計的輸出估計系統姿態角，通過卡爾曼濾波的形式補償系統姿態誤差.由於加速度的大小直接影響濾波器精度，本文設計了模糊自適應卡爾曼濾波演算法，根據三軸加速度計的輸出調整內阻尼量測誤差方差陣，從而避免了濾波器的發散.模擬和實驗驗證，內阻尼演算法可明顯抑制舒勒周期振蕩和傅科周期振蕩，避免了系統姿態漂移，有效提高了捷聯慣性航姿系統的精度
  5. Angles decrypted and software compensated with dsp and cpld, the angular displacement of the rotating set of axes with high resolution and precision can be obtained by taking the circular inductive synchronizer as the angle meter

    摘要用圓感應同步器作為測角元件，採取dsp和cpld進行角度解碼和軟體補償，可以得到極高解析度和測量精度的旋轉軸系的角位移數字量。
分享友人
分享到 Line

分享到臉書