端點力矩 的英文怎麼說

中文拼音 [duāndiǎnlìjǔ]
端點力矩 英文
end moment
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 端點 : extreme point; [數學] end point; extremity; terminal; end端點檢測器 end point detector; 端點控制 ...
  1. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  2. The prestressed continuous beam - arch composite bridges are a special structural system where the horizontal thrust of the arch rib is absorbed by a prestressed tie at deck level. in some cases, this type of structure is preferable because it does n ' t have the large thrust at the spring hi traditional arch bridges and the somewhat large bending moment and shear force in traditional beam bridges. as a result, the performances of the prestressing reinforcement can be efficiently utilized

    它利用拱肋承擔壓力，系梁預應力束抵抗拱端推力，吊桿及縱橫橋面系結構承受橋面荷載，既克服了傳統拱橋巨大的拱端推力，又改善了連續梁橋較大的彎矩和剪力的受力狀況，最大限度地發揮了拱梁混凝土和預應力鋼筋各自的特點，經濟效益顯著。
  3. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  4. Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied

    本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。
  5. The 16 - node degenerated iso - parametric element is proposed for the analysis of raft foundation with mid - thick plate. the stiffness matrix of single pile among the pile group can be founded assuming the total contact between the plate and the foundation. and the results of stress and deformation of plate, the force on pile and the settlement of pile bottom can be solved after the finite element disperse for the plate and the establishment of balance equation of pile - raft interaction

    在引入16節點退化等參元的中厚板筏板分析模型的基礎了，假定筏板與地基間完全接觸，建立了群樁中單樁樁身剛度矩陣，繼而對筏板進行有限元離散得到樁筏共同作用的平衡方程，從而求解筏板內力、撓度、樁頂反力、樁端沉降等一系列結果。
  6. Consequently time and cost can be saved greatly. ( 3 ) design method for controlling cracks in the negative moment zone of the continuous composite girder the crack mechanism of the concrete deck in the negative moment zone of the coniinuous composite girder, the relationship between the crack and the int

    分析認為，採用中間支點升降法與調整混凝土板施工順序相結合的施工方法，不僅可以避免負彎矩區混凝土裂紋，還可以合理調整鋼梁和混凝土板的內力，並使端支點與中間支點反力更均勻，使組合梁橋的結構更加經濟合理。
  7. 2 based on experimental results and finite elements analysis of new joint, the stress transfer mechanism of the new joint is analyzed. there are two stress transfer patterns about the new joint, one is for rectangular steel tubular column joint, its stress transfer pattern is that beam moment is transferred to column webs mainly by stiffeners, the other is for crft column joint, its stress transfer pattern is that part of beam moment is transferred from stiffeners to column webs, another part of beam moment is transferred to infilled concrete by column flange

    （二）基於新型節點的試驗結果和有限元分析，研究了新型節點的傳力機理，其應力的傳遞路徑分為兩種：對于鋼管柱節點，梁端彎矩主要通過加勁肋板直接傳至柱腹板，對于鋼管混凝土柱節點，梁端彎矩一部分通過加勁肋傳給柱腹板，另一部分通過柱翼緣傳給鋼管內的混凝土。
  8. According to the above formula, the initial rigidity and ultimate moment is calculated by developed program to several kinds of gabled frames end - plate connection joint with different types ( such as end - plate connection horizontally placed, vertically placed and inclinedly placed ), different end - plate thickness, different bolt diameter. the different result is compared with different end - plate thickness, the different force arm in joints, different bolt diameters and strength grades

    按推導的公式編程計算了不同形式（端板外伸式、端板平齊式、端板斜接、柱腹板加勁） 、不同端板厚度、不同螺栓直徑的門式剛架樑柱端板節點的初始剛度、節點極限彎矩，並比較了不同端板厚度、不同節點力臂、不同螺栓直徑和強度等級、不同連接形式下初始剛度和極限彎矩的變化。
  9. Experimental results show that the new cfrt - column to steel - beam joints proposed in this paper possess good earthquake resistant capacity. the infilled concrete benefit to restrain the buckling deformation of column webs, increase the strength and stiffness of the joint. the lengthened stiffener can transfer much more beam moment, make the strength of the joint increased

    試驗表明，在保證焊接質量的前提下，本文提出的新型方鋼管混凝土柱?鋼梁的節點具有良好的抗震性能；內填混凝土有利於抑制柱腹板的屈曲變形，增加節點的承載力和剛度；加勁肋長度的增加有利於傳遞梁端彎矩，使節點的承載力提高。
  10. Since railway is plunged into business, the wheelsets with two wheels fixed to two ends of one axle are commonly adopted in rail vehicle. the advantage of conventional fixed wheelsets is that they have self - steering capability produced by lognitudinal creep moments, however hunting unstability possibly occur when the speed of vehicle becomes higher, so independently rotating wheels are attached importance to increasingly

    自鐵路運營以來，鐵道機車車輛的輪對基本上都採用兩個車輪緊固在一根車軸兩端的形式，這種傳統固定輪對的優點在於它具有縱向蠕滑力產生的偏轉力矩從而使輪對具有自導向功能，但是在縱向蠕滑力矩的作用下，當車輛運行速度較高時就可能產生蛇行失穩。
  11. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  12. The two kinds of joint connection half - rigidity characteristic about gabled frames are discussed. the criterion among rigid connection, zero rigidity connection, half rigidity connection is determined ; the joint ' s moment and rotation angle curve is analyzed ; the calculation method about joint initial rigidity is brought forward ; the ultimate moment ' s calculation formula is deduced ; the result calculated by the formulas is compared to one calculated by the norm ' s formulas

    探討了門式剛架兩種端板節點連接的半剛性特性，確定了節點剛接、鉸接和半剛接劃分的標準；分析了節點受力時的彎矩轉角曲線關系；提出了節點的初始剛度的計算方法；提出了節點極限彎矩的計算公式，並與規范關于節點抗彎承載力計算的結果進行了比較。
  13. This paper studied the warp and stiffness of end - plate connection, and studied how the actual stiffness of end - plate connection influence stiff frame ' s displacement, and some design improvements are proposed. a methodology based on finite element modeling is used to establish strong bolted end - plate connection calculation model, and solved the interface between end - plates question and how to add bolt pretension when imitating end - plate connection ' s elastic material characteristic. through analyzing and comparing calculation results and experiment data, this paper summarized bolt force distribution, connection moment resistance, moment - rotation relationship and connection stiffness

    筆者採用有限元方法，建立高強螺栓端板連接的計算模型，模擬了節點彈性階段的工作狀態，較好的解決了高強螺栓端板連接中的接觸面問題和螺栓預拉力的施加問題，通過對計算結果的分析以及與實驗數據的比較，總結出端板連接在彎矩作用下的螺栓拉力分佈規律、節點抗彎承載力及其影響因素，以及節點剛度特性及其對剛架性能的影響，同時，對端板連接受力變形性能也做了十分有益的分析，為輕鋼節點設計方法的改進提供了依據。
  14. By way of these tendons, precest beams and columns can be assembled conveniently, and the joints and frame are monolithic and continuous. consequently, compared with common reinforced concrete frams, this kind of frame systems possess higher reliability and solved the problems in the process of assembling prestressed concrete frames. also it forms the framework of subassemblage and prestressed concrete frames, and explores a new way for industrial production of prestressed structures. by analyzing this system, a series of conclusion are provided, incluing modulation of bending moment produced by vertical loads within beam end, secondary internal forces produced by pretress force, shear resistance of the end of beams, the influence of lateral restrains. theresearch results of this paper are proved to be practical. some advices are also brought forward on the design process

    后張預應力筋既可作為施工階段拼裝手段，又可在使用階段承受梁端彎矩，構成整體受力節點和連續受力框架，克服了裝配式節點受力可靠性差的缺陷，解決了預應力混凝土框架難以裝配的問題，形成預制預應力混凝土裝配整體式框架，開辟了預應力結構工業化生產的新途徑。本文針對預壓裝配式預應力混凝土框架，從豎向荷載作用下的梁端彎矩調幅、施加預應力在框架中產生的次內力、梁端抗剪承載力、考慮側限的無側移框架的承載力分析四個方面對該種裝配式結構體系的性能做了詳細的研究。
分享友人
分享到 Line

分享到臉書