結晶槽 的英文怎麼說

中文拼音 [jiējīngcáo]
結晶槽 英文
crystallizer tank
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 結晶 : 1 （析出晶體） crystallize2 （晶體） crystal 3 （成果） crystallization; fruit; product; quintess...
  1. This paper proposes the use of steam condensate to wash the acidulation tail gas, then to be used as wash water for washing phosphogypsum, to be returned to the crystallizer, and a calculation is made of water balance in the system, so that the discharge of wastewater and waste gas is up to standard

    本文提出用蒸汽冷凝液洗滌酸解尾氣，然後用於洗滌磷石膏的洗水，返回結晶槽，並對系統的水平衡進行計算，可以實現硝酸磷肥生產的廢水和廢氣的達標排放。
  2. Abstract : a vertical sandwich deep trench with a field limiting ring is proposed to improve the breakdown voltage of power devices and high voltage devices. simulation result shows that nearly 100 breakdown voltage of the plane junction can be realized

    文摘:提出一種二氧化硅/多晶硅/二氧化硅夾心深槽場限制環新結構來提高晶體管的擊穿電壓.模擬結果顯示，該結構可以使射頻功率雙極性晶體管的擊穿電壓幾乎100達到平行平面結的理想值
  3. The tail gas absorption solution is returned to the crystallizer, thereby adjusting the liquid - solid ratio, and improving the phosphogypsum crystals with the entrained ammonium ions, with the result that the available components are recovered, and clean production and economic benefit are realized

    同時，尾氣吸收液返回結晶槽一方面可以調節液固比，另一方面帶入的銨根離子可以改善磷石膏的結晶，既回收了有效成分，又實現了清潔生產與經濟效益雙豐收。
  4. Further more, silicon is advantageous as the material of industrial temperature sensors, since its fabrication and processing techniques are well known. a novel method that get a 10um - 20um layer of single - crystal silicon as the temperature sensitive material and design transmitted configuration is presented

    論文在理論分析單晶硅透射特性的基礎上，提出了以微細加工各向異性腐蝕深槽的工藝方法，獲得10um 20um的單晶硅感溫薄膜，並採用透射式傳感結構。
  5. This thesis work has researched the fabrication technics of photonic crystal defect waveguide with air - bridge structure and collecting waveguide ; suggested using uv - lithography and wet etching to fabricate traditional waveguide, after that, using eb - lithography and dry etching to fabricate photonic crystal holes, so can reduce the fabrication cost by a big range ; designed the moulding board, which can fabricate the air - bridge structure and is convenient for recognizing position in eb - lithography ; the structure consisted of traditional waveguides and etching grooves are fabricated on soi successfully, then an successful eb - lithography is realized on the structure, the defect waveguide collected with the traditional waveguide quite well ; used the etching grooves to do the sacrificial layer etching experiment, which grounded etching sacrificial layer by photonic crystal holes in next step

    提出採用紫外光刻工藝製作傳統波導結構之後，通過電子束曝光和干法刻蝕製作光子晶體小孔的工藝方案，大幅度減低了製作成本；設計出可形成空氣橋結構、並且適用於電子束曝光位置識別的光刻模板，在soi材料上成功製作出帶有空氣橋刻蝕預留槽以及接續光波導的結構，在該結構上成功實現了光子晶體帶隙波導的電子束曝光，帶隙波導與接續光波導位置接續良好；最後利用預留槽進行了刻蝕犧牲層的實驗，為下一步利用光子晶體小孔刻蝕犧牲層形成空氣橋結構打下了基礎。
  6. The results show the grain size becomes larger along with elevated temperature and the grain size in interconnects does not change evidently after annealed at 200 ? because of the effect of the trench structure

    結果顯示熱處理后銅膜晶粒長大，但銅互連線薄膜由於溝槽結構對晶粒的長大有阻礙作用。利用xrd和ebsd測試方法對銅膜及銅互連線薄膜的織構進行評價。
  7. Then, a power - combiner has an output power over 1watt and a power - combining efficiency of 83 % at 34. 2 - 35. 5ghz was realized. small - signal gain and saturated output power were measured under both continuous wave and pulse wave

    利用小功率晶元設計8路開槽波導功率合成器，給出了連續波工作狀態與脈沖工作狀態的測試結果，包括通帶內小信號增益及飽和輸出功率。
  8. A vertical sandwich deep trench with a field limiting ring is proposed to improve the breakdown voltage of power devices and high voltage devices

    摘要提出一種二氧化矽多晶矽二氧化矽夾心深槽場限制環新結構來提高晶體管的擊穿電壓。
分享友人
分享到 Line

分享到臉書