裂紋片 的英文怎麼說

中文拼音 [lièwénpiān]
裂紋片 英文
crack gage
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 紋 : 名詞（花紋; 紋縷兒） lines; veins; grain
  • 片 : 片構詞成分。
  1. A craze is a thin platelike region.

    小裂紋是一個類似薄片的區域。
  2. It was concluded that failure of double clip reed was the result of local stress concentration and cracking at the sharp elbow of reed

    雙卡簧片成形時彎角較尖銳並有明顯裂紋是導致失效的原因。
  3. Abstract : by examining the technical processes of the cold - press dies on silicon - steel plates by metalloscope, the causes of cracks in the cold - press dies are analyzed, from which technical measures that are used to avoid cracking are derived

    文摘:通過對硅鋼片冷沖模各加工工藝的檢查和金相顯微觀察，分析了冷沖模產生裂紋的原因，並提出了防止裂紋產生的工藝措施。
  4. Live tuft is it point tiny tuft split, have various, distribute on if " the nail is sewn " in first form on the surface mainly to split, from form " burn caused by fire " that take the form of fish scale film in arriving, unanimous direction careful " detailed ox hair " of crackle, etc

    活綹裂指細小的綹裂，有各種各樣的，如主要分佈於表面上如甲狀的「指甲縫」 ，由表到內呈魚鱗片狀的「火傷性」 ，多呈一致方向細致裂紋的「細牛毛性」等。
  5. The fatigue cracks initiate in a intergranular manner and propagate in a transgranular manner, which stages are separated by secondary cracks

    實驗結果表明疲勞載荷下的橡膠裂紋首先沿片晶結合面萌生，然後穿晶擴展破壞，且存在次生裂紋。
  6. Study of the bonded repairing efficiency of the cracked plate with biaxial loading

    雙向受載裂紋板的復合材料補片膠接修補
  7. Study of cracked plate repair with composite patches under biaxial loading

    雙向受載裂紋板的碳纖維復合材料補片的膠接修補分析
  8. Analysis of axial - symmetric ring - shaped interface crack problems

    軸對稱環形片狀界面裂紋問題分析
  9. Combining with the results of implant test, the conclusion that the main reason of dropping the strength of austenite zone is the micro - crack located in the tip of flake graphite and marten site is drawn

    結合插銷試驗結果提出了馬氏體相變過程中，在片狀石墨尖端及馬氏體組織中造成的微裂紋是奧氏體區強度下降並進而在外力作用下斷裂的主要原因。
  10. Therefore one of efficiency means to solve cracking problem of runners is to change distribution of welding residual stress of blades, to decrease welding residual tensile stress in the dangerous area of blades or even turn to compressive stress

    因此，改變葉片焊接殘余應力的分佈狀態，降低葉片危險區域的焊接殘余拉應力峰值，甚至將危險區域的拉應力轉變為壓應力，是解決轉輪裂紋問題的有效途徑之一。
  11. For laminate containing penetrated crack, " two planes " model is introduced to analyze the influence of repair parameters on the strength of repaired laminate, including such as patch size, patch thickness, patch layout, the location of rivets

    摘要針對含穿透性裂紋的損傷層壓板，採用「兩板」模型建立起機械連接修補結構有限元分析模型，分別計算補片大小、厚度、鋪排方式以及連接件位置等修補參數對修補效果的影響。
  12. For the laminate which contains a crack, the suggested patch shape is rectangle, the patch thickness is equal to the parent laminate and the patch stacking sequence is the same as the parent laminate. because the length and the width of the patch have the fewer influence on the repair effect, the patch has the least weight on the basis of enough edge distance, end distance and space having been promised

    ?對于含裂紋復合材料層壓板，長方形補片的長度和寬度對修補效果沒有非常明顯的影響，因此在保證連接邊距、間距和端距的條件下，補片大小的選擇應該以節省重量為原則；而當補片的鋪排順序與母板相同、相對厚度為100時能夠獲得比較好的修補效果。
  13. Cracked and repaired specimens were tested under static load

    完成了復合材料補片修理單邊裂紋鋁板的實驗測試。
  14. The surface of nickel / plate should be smooth and neat without interlayer, crack, peeling, bubble and foreign substance

    帶材/片材表面應光滑、清潔。不應有分層、裂紋、起皮、氣泡和夾雜。
  15. Strength properties of holed aluminum alloy plate repaired with carbon fiber composite patches

    含中心裂紋鋁合金板的復合材料補片單面修補效果
  16. Based on the ultrasonic prompting, series of experiments about indt still had been done. the defect of metirical include aluminium honeycom seeper, aluminium tole microcrackle, aluminium honeycom board disglue, aluminium board microcrackle etc. the defect signal was distlled and analysed

    在此基礎上，應用超聲激勵，對系列試件缺陷，包括鋁蜂窩積水、鋁金屬薄片微裂紋、板形鋁蜂窩脫粘、鋁板微裂紋，進行了紅外無損檢測實驗，對缺陷信號進行了處理和分析。
  17. Cracks in francis turbine runner blades threaten the safety, stability and economic profits of the hydropower station

    摘要混流式水輪機轉輪葉片裂紋故障嚴重影響了水電站的安全穩定運行和經濟效益的發揮。
  18. The numerical simulation technique is used to study on the fatigue properties of submarine with high strength steel. the numerical simulation model is established and its feasibility is validated. at last, the possibility of establishing a kind of calculation and design methods of fatigue life in submarine structure is primarily analyzed

    本文把疲勞裂紋閉合模型通過切片合成法引入到潛艇結構疲勞強度計算上來，建立了潛艇結構疲勞強度的數字模擬計算的數學模型，分析該方法在潛艇結構疲勞強度計算上應用的可行性，為建立一套計算和設計潛艇結構疲勞強度的方法作了初步的探討。
  19. The opening stress and the life of crack growth is calculated and compared with the test results and the experience formula. the feasibility of the newman theory of opening stress used in the high strength steel is validated. then through the slice synthesis method, the three dimension surface crack of the weld joint of cone - cylinder is decomposed into many plane through cracks

    本文將基於裂紋閉合現象建立的帶狀屈服模型，用在平面貫穿裂紋中，計算此時的裂紋張開應力和疲勞裂紋擴展壽命，與試驗結果和經驗公式比較，驗證newman裂紋張開應力理論在高強鋼中的可行性；然後，用切片合成法，把潛艇結構凸錐柱結合殼焊縫處的三維表面裂紋分解成平面貫穿裂紋，用帶狀屈服模型的理論來分析平面貫穿裂紋，得到裂紋沿深度方向的擴展速率，進而得到潛艇結構的疲勞壽命。
  20. Therefore, it is important to know about the damage rule of particle separator, to analyze the degree of blade distortion by means of tests and calculations, to propose a set of vortex blade anti - impact ability appraisal methods

    因此，了解外物對渦流葉片的損傷規律，通過試驗和計算手段來分析葉片變形、產生裂紋或缺損的大小和程度，提出一套渦流葉片抗外物損傷能力的評估方法，對于粒子分離器的抗外物損傷設計是非常有必要的。
分享友人
分享到 Line

分享到臉書