誤差補償法 的英文怎麼說

中文拼音 [wùchābǔchángfǎ]
誤差補償法 英文
error compensation method
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 補 : Ⅰ動詞1 （修理; 修補） repair; mend; patch 2 （補充; 補足;填補） fill up; add supplement; supply; ...
  • 償 : 動詞1. （歸還; 抵補） repay; compensate for 2. （滿足） meet; fulfil
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 誤差 : error
  • 補償 : compensate; make up; make up for; make it up to sb. ; make sth. good; compensation; offset
  1. Color image segmentation based on fuzzy logic

    基於模糊優化演算法的慣性元件誤差補償方法
  2. In general, a precise resistor is in series with one of the resistors in wheatstone bridge to compensate the zero offset, and the other one is in parallel with another arm of the wheatstone bridge to compensate thermal zero drift. based on this principle, in this paper, a compensation method based on virtual instrument technology has been put forward. actuated by current source, a good calculation method of compensation resistors and their position in the bridge is deduced

    本文基於串並聯電阻補償法的原理，提出了一種基於虛擬儀器的誤差補償方案，推導了在恆流源供電下可以精確的計算出補償電阻大小和補償位置的演算法，並且在虛擬儀器軟體平臺labview上完成了數據採集、處理、顯示等軟體的設計，經過實驗的驗證，對傳感器的零點溫度漂移補償取得較好的效果，而對靈敏度溫度漂移的工藝補償亦有一定的效果。
  3. Third step is using modifying method and the compensating method to increase the scara assembly robot precision. the emulator testified that the error model and the correlative theory is legitimacy

    模擬結果驗證所建立的機器人位姿誤差理論的正確性，位姿誤差補償、運動學參數誤差優化分配方法對于提高機器人精度的實用性。
  4. With the experiment part, the errors of sk - 21 nc machine tool have been measured, and a serial of data is gotten which lead to the error discrimination. ( 3 ) based on the kinematical theory of mbs, the calculation methods for the ideal center envelop curve of grinding wheel on cam grinding, the practical cutter track, inverse contour of cam, ideal nc instructions, precision nc instructions, the inner / outer normal and the fitting criterion of curve have been all discussed in detail in this paper

    （ 3 ）通過精密加工的約束條件方程，探討理想刀具路線、逆變數控指令與實際刀具軌跡之間的映射關系，解決誤差補償技術提高加工精度的核心問題? ?當要求數控磨床的砂輪中心準確到達給定的理想點時，精密數控指令值究竟該是多少，如何能夠通過計算，獲得這樣的數控指令值，給出經修正的數控指令計算方法。
  5. We mainly discuss the methods of gmti, location, and the measure of velocity, the decrease of false alarm probability and the compensation for phase error

    主要研究mcarm數據動目標的檢測、定位和測速的方法，利用定位和測速信息進一步降低虛警概率的方法和相位誤差補償方法。
  6. In chapter 2, author points out firstly that the elastic deformation of elastic units of a robot ' s wrist force sensor will be enlarged by the end - effector, the instruments and the work pieces, so the elastic deformation of the sensor will influence the location accuracy or kinetic accuracy of end point of a robot, under the condition of that the robot technology facing the developing of heavy load, light mass and high accuracy. it is discussed respectively that the relationship between the differential kinemics in the sensor ' s coordinate and the location accuracy or kinetic accuracy of the end point. error matrixes of location and kinemics of the end point are presented respectively based on the differential kinemics in the sensor ' s coordinate, and the on - line error compensation methods are introduced subsequently

    第二章首先指出機器人腕力傳感器彈性體的彈性變形經過機器人末端連桿、工具、工件等的放大后，會對機器人末端精確定位和運動產生的影響；然後分別研究了傳感器坐標系內的微分運動與機器人末端工件精確定位、運動的關系；在此基礎上，研究了基於腕力傳感器彈性體微分運動的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；基於機器人動力學的機器人末端定位、運動誤差的誤差矩陣及其在線誤差補償方法；最後，以puma型機器人為對象，給出了基於腕力傳感器內微分運動的機器人末端定位、運動誤差及其在線補償方法的模擬實例：給出了基於機器人動力學的機器人末端定位、運動誤差及其在線補償方法的模擬實例；模擬結果表明， 1 ）基於腕力傳感器的機器人末端定位誤差在腕力傳感器允許的載荷下可達十分之幾毫米級。
  7. And a novel method via initial determined error compensation is presented in order to reduce the influence of shop motion and lever - arm effect

    並提出了採用初始裝定誤差補償的方法消除船舶運動與桿臂效應對射擊的影響。
  8. This paper first researched the general situation of domestic and abroad developments in the field of ultra - precision aspheric surface machining technology and its numerical control system, analyzed the aspheric surface machining principle of ultra - precision machine, and in these bases, founded the kinematics model of ultra - precision machine in ideal condition using the homogeneous coordinate conversion method in robotics

    分析了本實驗室超精密機床非球面加工原理，在此基礎上應用機器人學中齊次坐標變換的方法建立了理想情況下超精密機床運動學模型，通過綜合分析超精密機床的運動誤差，給出了超精密機床的誤差補償模型。
  9. 4. suboptimal fading ddf ( sfddf ) and suboptimal fading ukf ( sfukf ) algorithm can be obtained with the application of suboptimal fading ekf. suboptimal fading algorithm is an error compensative technology basing on the kalman filter orthogonality principle, which can greatly improve filtering precision and stability

    4 、把一種帶次優漸消因子的ekf演算法推廣到ddf和ukf演算法中，得到sfddf和sfukf演算法，次優漸消因子是一種基於kalman濾波正交原理誤差補償技術，它的引入較大的改善了濾波精度和演算法穩定性。
  10. In this paper, the application of dsp technology in electric power measurement meter has been studied, meanwhile analysed the error of the electronic energy meter, put forward the measure to compensate error with software method. it not only changes the precision degree of electric power measurement meter, but also avoids the disadvantage from error compensate with hardware method, it is unnecessary to adjust the sample value of voltage and electric current in circuitry

    對dsp技術在電度表中的應用進行了研究，對電度表系統的誤差進行了分析，提出了採用軟體方法來補償誤差的措施，使電度表的精度達到了設計要求，又避免了利用硬體進行誤差補償所帶來的弊端，不用在線路中調整電壓、電流采樣值，有利於生產。
  11. Then we use the data of corner position to adjust the first data we get by the fast aiming. using this method, we can improve the aiming speed and make the operators less tired. the measurement system could solve the dimension measurement problems in the transformer factories, and it can be applied to wider fields

    論文實現的攝像人工瞄準方法帶來的誤差可控制在0 . 008mm范圍內，達到系統要求，具有實用價值；快速瞄準后自動誤差補償在選用合適的硬體后能大幅度提高瞄準速度，並能簡化機械設計。
  12. Compensation for the errors of the strapdown arithmetic in sins

    捷聯慣導系統的捷聯演算法誤差補償
  13. Iv ) constructing of a kind of approximate integration conservative remapping algorithm. through analyzing a second order sign - preserving conservative remapping method, two conservative remapping algorithms have been constructed by using the reconstruction method to take the place of the positivity - preserving error compensation algorithm

    （ 4 ）近似積分守恆重映方法構造：在分析了二階保號守恆重映方法的基礎上，通過重構的方法代替原演算法中的誤差補償方法，構造了兩個守恆重映方法。
  14. The whole article consists of 6 parts : 1. object of the project and the development background of the relative technique are introduced. 2. the theory of the micro inertial heave height measurement is depicted. 3. arithmetic model base on matlab / simulink for micro inertial heave height measurement is offered, including the result analysis for the simulation. 4. the whole hardware design base on aduc841 single chip of the mimu data collection system is depicted. 5. software design is introduced. 6. adjusting and error compensation model of the mems is depicted. at last, sum - up, view and enhancement of the system are given

    本論文分成六個部分:第一部分介紹了課題研究的目的及相關技術的發展概況;第二部分主要論述微慣性測高的理論基礎;第三部分給出微慣性測高演算法的matlab模擬模型及模擬結果分析;第四部分給出基於微慣性傳感器及aduc841單片機的微慣性數據採集系統的硬體設計及調試方案;第五部分為微慣性數據採集系統的軟體設計;第六部分介紹了微慣性傳感器的標定及誤差補償方法。
  15. In the process of establishing model of ball - end cutter milling forces, the algorithm of determining cutter eccentricity parameters are presented to integrate the condition of single edge cutting. the cutter eccentricity parameters are decided by using the above algorithm in the process of calculating milling force coefficients according to the experiment data of milling force. results of experiment show that the simulation algorithm is satisfying

    4 .提出了球頭銑刀刀具磨損的衡量方法，建立了磨損模型，用以衡量由刀具磨損而可能產生的加工誤差;建立了球頭銑刀在端銑加工中因刀具變形而可能產生的加工誤差模型;提出了相應的由於刀具磨損和刀具變形引起的加工誤差補償方法。
  16. One novel non - linearity compensation method is proposed based on the parameters estimation of the discrete interference signals. the effectiveness of the compensation method considering phase - quarter errors, unequal amplitude and the dc components are simulated

    在研究干涉測量非線性誤差補償原理的基礎上，提出一種基於待檢偏測量信號參數估計原理的非線性誤差補償方法。
  17. The deviation introduced by reference phase shifting errors on four - steps and five - steps algorithm are analyzed. based on the principle of phase algorithm, a novel compensation method of reference phase - shifting error is described for four - steps algorithm and the five - steps algorithm. the theoretic analysis and data simulation indicate that the phase deviation arising from the first and the second harmonic reference phase - shifting errors can be eliminated using this method

    在研究相位偏移干涉測量技術基礎上，重點研究了五幅演算法計算精度及移相誤差對計算結果的影響；提出了四幅演算法及五幅演算法移相誤差補償方法，理論分析及模擬模擬結果顯示，該方法可以補償移相過程中一階移相誤差及二階移相誤差對相位偏移干涉測量精度的影響。
  18. To develop the system to an automatic system, we have studied how to improve measurement precise by image processing after fast aiming. we use median filter to filtrate noise, use sobel arithmetic to detect the edge, and use kitchen - rosenfeld method to detect corners

    第一種方法著重研究了視頻採集和屏幕懸浮透明瞄準坐標系的同步顯示以及提高瞄準精度的途徑；第二種方法則著重研究快速瞄準后通過圖像處理技術自動獲得誤差補償數據。
  19. A new weighted modeling algorithm is presented and the weight value learning algorithm is solved, another integrated modeling method is also presented. two models can improve the precision compared to the traditional algorithm

    首先對基於矢量法的誤差綜合模型進行了改進，將刀具磨損考慮其中，這樣使得誤差模型更為全面，並且提出了誤差補償的實現方案。
  20. Due to its character of microscopic scale motion, a very simple position kinematic equation is achieved. based on the equation obtained, the workspace of the serial - parallel micromanipulator is described, and the effect of different structural parameters on the workspace is also discussed. in order to evaluate the output errors caused by the structural errors and actuator errors, accuracy analysis is then conducted for this serial - parallel micromanipulator, and an approach based on software programming is presented for error compensation

    由於所研究的微操作機器人運動范圍很微小，機構結構誤差及驅動誤差都可能造成機器人的操作精度嚴重降低，為評價這些機構誤差對運動精度的影響，本論文以矢量法對該機器人機構進行了誤差分析，並討論了誤差補償的軟體法；此外，論文還進一步研究了遺傳演算法在並聯機器人機構學研究中的應用，為並聯機器人位置正解問題求解提出一種新思路。
分享友人
分享到 Line

分享到臉書