轉矩波動 的英文怎麼說

中文拼音 [zhuǎnjǔbōdòng]
轉矩波動 英文
torque fluctuation
  • 轉 : 轉構詞成分。
  • 矩 : 名詞1. （畫直角或正方形、矩形用的曲尺） carpenter's square; square2. （法度; 規則） rules; regulations 3. [物理學] moment
  • 波 : Ⅰ名詞1 （波浪） wave 2 [物理學] （振動傳播的過程） wave 3 （意外變化） an unexpected turn of even...
  • 波動 : 1 （不穩定） undulate; fluctuate; unsettle; surge; rise and fall 2 [物理學] wave （motion）; wave...
  1. Two nonlinear simulation methods are designed by curve fitting method and anfis which seem simply and right in the simulation experiment. based on the model different control strategies also were realized in detail such as chopped current control ( ccc ), angular position control ( apc ), amplitude - change ccc and pi control. a simple torque sharing function ( tsf ) method and a tsf controller were designed which decreases torque ripple effectively

    文章中還建立一種基於模糊神經網路的非線性模型，並對比分析了三種方法，模擬中確定了電機的最優開通關斷角，在此基礎上實現了電流斬波控制、角度位置控制、變幅值電流斬波控制以及分段雙閉環pi控制，模擬結果表明，它實現了電機的正常運行，很好的抑止了電機轉矩脈動，同時有效地降低了噪聲。
  2. Secondly, the effects of the crest width of the back - emf waveform to the torque ripple in the 120 ? conduction mode are analyzed, among which the effects of the advance commutation angle to the torque ripple are quantificationally analyzed for the bldcm drives whose back - emf waveform crest width is less than 120 ?,

    其次分析了120導通方式下反電動勢平頂寬度對轉矩脈動的影響，對于平頂寬度小於120電角的非理想梯形波反電動勢，定量分析了換相超前角對換相轉矩脈動的影響。
  3. For the bldcm which has a pseudo - sinusoidal back - emf waveform, this dissertation presents a svpwm control method using six discrete position signals for minimizing the torque ripple. the main aspects for the implementation of this method are analyzed, including the initial orientation of the voltage vector, reasonable choice of the impedance angle and the advance commutation angle, and estimation of the successive rotor positions

    針對反電動勢類似正弦的準正弦波反電動勢無刷直流電動機，本文提出一種基於六個離散位置信號的自同步svpwm （電壓空間矢量法）控制方法，用以削弱電磁轉矩脈動，分析了實現這種方法的主要控制環節，包括起動時電壓空間矢量的初始定位，阻抗角與電流超前角的合理選擇以及連續轉子位置的估計等。
  4. Furthermore, this dissertation also gives a comprehensive analysis and comparison to the torque ripple factor, torque - current ratio and other aspects for pseudo - sinusoidal emf bldcm drived by 120 conduction mode, 180 conduction mode and self - synchronous svpwm mode respectively. the simulation and the experimental results indicate that self - synchronous svpwm method is more effective for minimizing the torque ripple without any expense of the torque - current ratio when the crest width of the back - emf waveform is less than 107 electrical angles

    對準正弦波反電動勢無刷直流電動機在120導通方式、 180導通方式和自同步svpwm三種控制方式下的轉矩脈動系數、轉矩電流比等方面進行了全面的分析與比較，模擬研究和實驗結果表明，當反電動勢的平頂寬度小於107電角時，採用自同步svpwm控制方法可以在不損失轉矩電流比的基礎上，更有效地抑制電磁轉矩脈動。
  5. For the bldcm which has a general crest width of the back - emf waveform, two kinds of torque ripple conditions when drived by sine - wave current as well as by square - wave current are deduced based on the mathematical models. in addition, a comparison is carried out between these two conditions, which indicates that sinusoidal current driving is more favorable to minimizing the torque ripple when the crest width of the back - emf waveform is less than a certain value

    闡述了抑制齒槽轉矩措施對反電動勢波形的影響，利用無刷直流電機的數學模型推導並比較了任意平頂寬度梯形波反電動勢在正弦波和矩形波兩種電流驅動下的電磁轉矩脈動情況，得出在梯形波平頂寬度減小到一定數值后採用正弦電流驅動更有利於減小電磁轉矩脈動。
  6. 3. with fourier decomposition, the main component of pulsating torque, torque ripple is studied. it can be determined that torque ripple is caused by harmonic order 6n under the usual common conditions

    3 、對造成轉矩脈動的主要成分轉矩紋波進行諧波分析，得出在一般假設情況下，無刷直流電動機系統的轉矩紋波由電磁轉矩的6n次諧波造成的結論。
  7. The study has completed the design of two - phase inverter and made up of the two - phase inverter - motor system for experimental use it is a variable frequency adjustable speed system with a open - loop control of rotational speed, which consists of voltage - controlled oscillator circulating assign device inverter circuit and two - phase induction motor a accurate mathematical model is set based on the whole system, and simulator program of dynamic and steady condition is established, which is used to calculate the dynamic and steady performance by kron and symmetrical coordinate converter by simulator calculation and experimental research with specific parameter of the system, a comparison is made between predicted and experimental characteristics, experimental measurements are shown to compare closely with corresponding theoretical result it is compared with some variable frequency adjus table speed system comprising inverter and single - phase induction motor from the system efficiency torque pulsation and the effect of two - phase inverter capacitance based on the conclusion, harmonic cancellation pulse width modulation control of a two - phase inverter - fed induction - motor drive system is researched, which cancelled the low harmonic and improve the system performance

    通過對電機的kron變換和對稱分量變換，建立了系統較精確的數學模型，編制了系統動態及穩態運行的模擬計算程序分別計算系統的動態和穩態性能。通過對系統的具體參數進行了模擬運算和實驗研究，實驗和模擬結果進行比較，說明實驗和理論較為一致，並從系統效率、轉矩脈動及兩相逆變器電容的影響等方面與各種逆變器和單相異步電動機組成的變頻調速系統加以比較。在此基礎上，對兩相逆變器供電-異步電動機系統使用諧波抑制pwm控制進行了研究，由於減少了低次諧波，改善了系統性能。
  8. Fuzzy control method of commutation torque ripple minimization for bldcm

    用模糊控制方法抑制無刷直流電動機換相轉矩波動
  9. It is showed that the torque ripple is not only connected with the phase currents, but also with the other factors, such as the instantaneous phase emf ' s in the case of commutation, the angle of commutation and the parameters of the windings

    從一個新的角度分析了繞組換相引起轉矩波動的原因，指出換相轉矩波動不僅與電機繞組電流有關，還與換相時相繞組感生電勢瞬時值、換相位置角、繞組參數等因素有關。
  10. 8. a pulsating torque minimization approach based on disturbance observer is proposed. the new disturbance observer is designed to observe the unknown torque disturbance caused by the torque ripple, the varying of the motor parameters, the changing of load torque and the not ideal performance of the inverter

    該系統將負載轉矩、轉矩紋波以及由電機參數的變化引起的轉矩干擾作為系統干擾，用干擾觀測器進行觀測，以此為基礎對轉矩脈動進行補償，實現對轉矩脈動的抑制。
  11. In the proposed technique the bemf waveform of bldcm need to be measured in advance at first, through computer simulation and frame transformation, the optimum q - axis current command is achieved. in order to minimize the torque ripple, the d and 0 - axis current command should be zero. furthermore, through reference frame transformation from dqo - axis to abc - axis, we can get the optimum current command in static abc reference frame

    在這種控制方法中首先測量出電機的實際反電動勢波形，然後通過計算機擬合和坐標變換，求得產生恆定電磁轉矩所需的q軸電流，令i _ d ~ * = i _ 0 ~ * = 0 ，通過坐標變換，得到三相靜止坐標系a - b - c下的參考電流i _ a ~ * ， i _ b ~ * ， i _ c ~ * ，利用電流滯環控制來產生pwm信號，由於這種控制方法中電流不會突變，從而可以較好的抑制轉矩脈動。
  12. The ideal bemf waveform of bldcm is trapezoid with 120 ! platform width. in the 120 conduction mode, the stator current is not ideal due to the stator inductance, and the torque ripple occurs

    理想的永磁無刷直流電動機的反電動勢的波形是120平頂的梯形波，在三相六狀態120導通方式控制下，電流由於電機定子電感的存在而不是理想方波，因此產生了換相轉矩脈動。
  13. However, the waveforms of motor currents are difficult to control. the harmonic components of the current will produce torque pulsation, additional losses and some emi problems

    電壓源方式主迴路比較簡單，但電流波形難以控制，且諧波所帶來的轉矩脈動和損耗比較大， emi問題難以解決。
  14. In order to minimize the commutation torque ripple of traditional trapezoidal bldcm using 120 cconduction mode, firstly, analytical formulae of commutation torque in the condition of perfect back - emf waveforms are developed in this thesis, based on which the effects to the torque ripple by the pwm modes, overlapping commutation techniques and so on are analyzed, and the applicable speed ranges of the motors using the overlapping commutation techniques are derived

    為了抑制傳統的三相六狀態120導通方式控制下方波型無刷直流電動機的換相轉矩脈動，本文首先在理想反電動勢的條件下推導了換相轉矩脈動的解析公式，並由此分析了調制方式、重疊換相技術等對換相轉矩脈動的影響，得出了採用重疊換相技術抑制換相轉矩脈動適用的電機轉速范圍。
  15. Second, a direct torque control for pmsm based on stepping spwm is analyzed. in classic dtc system, the torque and current ripples are larger because of the restriction of the number of voltage vectors. by means of the vectors subdividing theory, using a new method of dividing voltage vectors based on stepping spwm, more voltage vectors on a circle in space can be achieved

    其次考慮到上述的經典的dtc演算法中，由於電壓矢量個數（六個）的限制，使得轉矩波動和電流波動都比較大；針對於此，本文利用矢量細分原理，提出了新的基於階梯spwm的電壓矢量生成方法，得到了更多的空間上均勻分佈的電壓矢量，可對電壓矢量進行更加有效的選擇。
  16. Abstract in this paper the phase commutation and current curves of brushless motor variable - speed system are studied. according to the results that the pulsating torque is influenced greatly by the ratio of the direct current supply voltage and the electromotive force of the motor, an approach to reduce the pulsating torque is presented

    本文通過對無換向器電動機模型的換相過程和電流波形的研究，得到換相轉矩波動受直流電源電壓和電動機電動勢幅值的比（ u / e ）的影響較大的結論並獲取了最佳u / e ，同時通過模擬研究了電流波形，提出了減小轉矩脈動的控制策略。
  17. The paper analysis the torque ripple effected by electric magnetic factor influences the performance of motor, and presents the measures of reducing torque ripple

    重點分析了因電磁原因引起的轉矩波動及其對電機性能的影響，提出了減小轉矩波動的措施。
  18. At last the writer presents a new kind of control method in the paper. it tries to solve the problem of torque fluctuation only by change of control method, not by change of motor substratum

    最後，本文還提出了一種新型的電機控制方式，這種新型控制方式旨在不改變電機本體的設計而只是通過控制方式的改變來解決通常的控制方式帶來的轉矩波動過大的問題。
  19. In the meantime, the paper introducted the method of fixed - frequency sampling in combination with commutation method by overlap in order to hold back the torque ripple of bldcm

    論文主要研究了兩相和三相無位置傳感器永磁無刷直流電機由電流換相引起的轉矩波動，推導出相應的轉矩波動公式，提出一種採用定頻采樣和重疊換相相結合的方法對換相轉矩波動進行抑制和控制。
  20. The effect of each referred factor on the commutation torque ripple is calculated by the numerical computation so that the foundation is theoretically established for further research for reduction of commutation torque ripple, the design and control of the brushless dc motors

    通過數值計算結果說明?各因素對換相轉矩波動的影響程度，為研究換相轉矩波動的減小措施和永磁無別電機的設計及控制提供了理論依據。
分享友人
分享到 Line

分享到臉書