鍍層質量 的英文怎麼說

中文拼音 [dùcéngzhíliáng]
鍍層質量 英文
coating mass
  • 鍍 : 動詞（用電解或其他化學方法使一種金屬附著到別的金屬或物體表面上） plate
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  • 質 : Ⅰ名詞1 （性質; 本質） nature; character; essence 2 （質量） quality 3 （物質） matter; substance;...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 質量 : 1 [物理學] mass 2 （產品或工作的優劣程度） quality 3 economy （離子源的）; 質量標準 quality level...
  1. Liberation of hydrogen gas would be increased rapidly and sic particles on the surface might be dispersed if the current density exceed the upper limit. furthermore, nickelous hydroxide would be deposited because the ph of plating solution nearby the surface rapidly increased. all of above might result in coating deterioration

    若電流密度過大，超過所允許的上限值，會析出大量的氫氣，可能沖散表面覆蓋的sic微粒，而且易使磨頭表面鍍液ph值急劇上升而形成氫氧化鎳沉澱，導致鍍層質量惡化。
  2. The relations between corrosion resistance of chromium plating and technology, quality, matrix materials and surface processing methods were studied based on the summaries of production practices, arid also the methods to improve corrosion resistance were put forward

    摘要在總結實踐生產經驗的基礎上，研究和探討了硬鉻鍍層的耐腐蝕性能與鍍鉻工藝選擇、鍍層質量、基體材質和表面加工質量及方法的關系，提出了達到高耐腐蝕性能的方法。
  3. Methods to improve the quality of inner electroplate of connector with small and deep holes

    深孔接觸件電鍍中孔內鍍層質量的方法
  4. Standard specification for steel sheet, coated by the electrolytic process for applications requiring designation of the coating mass on each surface general requirements

    要求標定每面鍍層質量的電解塗鍍薄鋼板的標準規范
  5. Aluminium and aluminium alloys - anodizing - assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid chromic acid solution with prior acid treatment

    鋁和鋁合金.陽極氧化.測定預先酸處理的浸入磷酸鉻酸溶液后質量損失評估密封陽極氧化鍍層質量
  6. Aluminium and aluminium alloys - anodizing - assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid chromic acid solution without prior acid treatment

    鋁和鋁合金.陽極氧化.測定未預先酸處理的浸入磷酸鉻酸溶液后質量損失以評估密封陽極氧化鍍層質量
  7. Mass calculation of coating for equal coating mm

    鋅鍍層質量兩個相同鋅鍍層厚度
  8. Mass calculation of coating for differential coating mm

    鋅鍍層質量兩個不同鋅鍍層厚度
  9. The formulae that didn " t contain fluorine had low rates of corrosion, high stability and easy operation and had distinct improvement in coating quality, surplus of chromium, saving electricity and energy and environmental protection etc. when they were compared with the commercial additive of wr - 1 and the electrolyte formula of fenghui galvanization plant, the results showed that the effect of chromium plating of the formulae obtained in this study are more excellent

    所研製的配方，不含氟、腐蝕率低，穩定性好，易操作，在鍍層質量、節鉻、節電、節能、環境保護諸方面都有明顯的改善，並將其與市售的wr 1添加劑和淬惠電鍍廠鍍鉻效果進行了對比，結果表明本研究得到的配方鍍鉻效果更優良。
  10. Especially under the high temperature and medium current d ensity, it can strikingly improve the integrated properties of coating. the recombination of rare earth with organic additive can make up for the weak of single addition of rare earth

    稀土對鍍層質量影響較大，尤其是在高溫中等電流密度時，可大大改善鍍層的綜合性能，而稀土與有機添加劑復合可彌補單一添加稀土的不足。
  11. Standard specification for steel sheet, zinc coated by the electrolytic process for applications requiring designation of the coating mass on each surface

    每面鍍層質量應予標明的電解鍍鋅薄鋼板標準規范
  12. Standard specification for steel sheet, zinc - nickel alloy coated by the electrolytic process for applications requiring designation of the coating mass on each surface

    每面鍍層質量應予標明的電解鍍鋅鎳合金薄鋼板標準規范
  13. Zinc coating mass

    鋅鍍層質量
  14. Grade plating type designation of coating mass common coating mass

    級別電鍍方法鍍層質量及常用稱號
  15. The purpose of the study was to improve properties of the traditional zinc electrodeposits

    為解決傳統工藝中所存在的鍍層質量問題，研製出一種專用於線材硫酸鹽鍍鋅的組合光亮劑。
  16. Aluminium and aluminium alloys - anodizing - assessment of quality of sealed anodic oxidation coatings by measurement of admittance

    鋁和鋁合金.陽極氧化.通過導納測量評估密封陽極氧化物鍍層質量
  17. The action of composite of purely inorganic additives on improving coating quality is worse than that of composite of purely organic and organic and inorganic additives

    單純的無機添加劑復合對改善鍍層質量的作用要小於有機?有機復合以及有機?無機復合的作用。
  18. It was pointed with the experiment methods of electro - chemistry, metallographic analysis, weighing, spot count and bending that : the additives play an important part in getting high quality coating. however, the effect of different kinds of additives on performance of electrolyte and coating and the part of same additive in different electrolyte are varied. each additive is selective to electrolyte

    通過電化學方法、金相組織分析、重量法、斑點法、彎曲法等試驗方法研究指出：添加劑對鍍層質量起著至關重要的作用，但不同類型的添加劑對鍍液和鍍層性能的影響並不相同，同一添加劑在不同鍍液中所起作用亦有差異，各種鍍液對添加劑具有選擇性。
  19. The optical fiber surface pretreatment craft processes and the technological conditions have been determined through the experiment, various craft procedures which influence the electroless plating nickel - phosphorus alloy coating quality have been analyzed, the most attentions have been put on the coarsening and the activation craft which determine the electroless coating quality

    本文通過試驗確定了光纖表面預處理的工藝流程及其工藝條件，分析了各工序對化學鍍鎳磷合金鍍層質量的影響，重點研究了粗化及活化對化學鍍層質量的影響。
  20. The coating adhesion was detected by scribe - grid test and thermal shock test. the morphology of the coating was charactered by metallographic microscopy and sem. the research results of the experiments show that : 1

    研究結果表明: 1 .採用草酸酸洗、堿性活化、配合劑鉀鹽浸鋅液浸鋅的前處理獲得的后鍍層質量高。
分享友人
分享到 Line

分享到臉書