高溫裂解 的英文怎麼說

中文拼音 [gāowēnlièjiě]
高溫裂解 英文
pintsch process
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 裂 : 裂動詞[方言] （東西的兩部分向兩旁分開） open
  • 解 : 解動詞（解送） send under guard
  • 高溫 : high temperature; elevated temperature; hyperthermia; megatemperature; inferno
  1. Heaters of high temperature, such as soldering irons, should be kept away from the vinyl insulation sleeve of capacitor which to avoid the cause made over heat or break down to sleeve

    電烙鐵等高溫發熱裝置應與電解電容器塑料外殼保持適當的距離，以防止過熱造成塑料套管破裂。
  2. This paper introduces the aging mechanisms of bio - oil and various methods to improve the stability of bio - oil, including drying, deashing, hot - gas filtration, vapor - phase catalytic pyrolysis, adding solvent and mild hydrogenation, etc

    介紹了導致生物油不穩定的機理和各種提高生物油穩定性的方法，如原料乾燥、酸（水）洗脫灰、氣體高溫過濾、氣相催化裂解、添加溶劑和生物油適度加氫等。
  3. While still not evidenced in our experiment, liquid - phase doping of ammonium molybdate solution has been broadly agreed to be able to significantly increase the yield of swnts. we have developed another doping method, solid - phase doping of metal molybdenum at elevated temperature, and discovered that sol - gel prepared catalyst with such doping can be used to grow multi - wall carbon nanotube bundles in a very large scale

    對催化劑進行摻鉬處理表明，它可顯著提高催化劑催化裂解甲烷合成納米碳管的能力：作者在高溫下進行了催化劑摻入金屬鉬的實驗，得到了一種性能優異的催化劑，以此制備的多壁納米碳管的呈束狀分佈，所得的粗產物與催化劑之間的重量比達15倍以上。
  4. We research the causes of concrete cracking, develop the high performance anti - cracking additive, optimize the concrete mix and construction techniques, increase the stability of concrete volume by shrinkage compensation, enhance splitting tensile strength, and can meet demand of high workability of fresh concrete. in the study, a thorough investigation of this problem is made from all points of view, with the aid of various modern measurement & testing technology and different theories & methods in surface physical chemistry, structural chemistry, solid - state chemistry, composite materials, fracture mechanics, etc. our research results have shown that the various shrinkage of concrete cause concrete cracking in building engineering, such as autogenous shrinkage, dry shrinkage, temperature shrinkage, plastic shrinkage, carbonized shrinkage, etc

    目前，解決混凝土開裂的方法是綜合的，我們調查研究了混凝土開裂的原因，開發研製了高性能抗裂外加劑，優化混凝土的設計和施工方法，並通過補償收縮達到混凝土體積穩定，提高抗裂強度，滿足混凝土拌和物高工作性能的要求。本研究採用多種測試技術，應用表面物理化學、結構化學、固體化學、復合材料學、斷裂力學等多學科的理論與方法，從不同的角度進行深入的研究和探討。通過調查研究建築工程中出現的混凝土開裂、滲漏問題，發現混凝土在非荷載作用下開裂主要是由混凝土的自收縮、乾燥收縮、溫度收縮、塑性收縮、碳化收縮等各種收縮變形引起的。
  5. On the basis of the former research, we studied the cause of cff ’ s craze and sparkle and put forward a method to resolve these problems by means of the optimization of the making process. the developed ceramic foam filter that could filer 82 kilogram 1700 c melted casting steel has excellent performances

    本研究在前期試驗的基礎上，通過優化、穩定泡沫陶瓷過濾器的制備工藝，分析並解決了試樣中出現的通孔率低、表面質量差和部分試樣開裂的問題。所制備的泡沫陶瓷過濾器已具備可持續過濾82公斤1700 c鋼液的較好高溫性能。
  6. Determination of pyrolysis products for com straw by gc - ms

    法測定玉米秸高溫水蒸汽裂解產物的組成
  7. The results showed that hydrothermal cracking occurred while injecting steam, and the catalyst had catalytic activity for hydrothermal cracking of heavy oil at higher temperature ; viscosity and average molecular weight of heavy oil was thus lowered

    實驗結果表明，在注入蒸汽的條件下，遼河稠油可以發生水熱裂解反應，高溫下催化劑對水熱裂解反應具有催化作用。
  8. Thermal stability the property of a lubricant which indicates its ability to resist cracking and decomposition on prolonged exposure to elevated temperatures

    熱穩定性表明潤滑油在長期高溫環境中抵抗裂化和分解能力的指標。
  9. Series of high pressure thermocouples thermalresistances and thermowells, the thermocouple take the form of spring - loaded, of which protective tube and flange are forged of special alloy, as well the thermowell are formed with bar stock drilled. more further, theconnecting between thermowell and flange can be compressed with tapered thread and the groove at the lower end of flange can be welded with argon arc. these thermocouples are usually used in high equipments of hydrogen cracking device, cracker and vaporizer etc for pressure - resistant in over 30 mpa, operating temperature from 0 up to 800

    系列高壓熱電偶阻及套管，熱電偶採用彈簧壓著式，保護套管和法蘭選用特殊合金材料鍛造，套管採用棒料整體鉆孔加工而成，與法蘭連接處以錐管螺紋配合併與法蘭下端渠槽處用氬弧焊接，耐壓30mpa ，使用溫度0800 ，可長期使用在加氫裂化裝置裂解裝置，氣化爐等高壓設備中。
  10. We think increase of the internal resistance of battery is the main problem to the recycle life deteriorating at high rate, besides the influence of the materials. decomposition occurred on positive and negative electrode at high rate current and the interspaces increased. the restrains of swelling and the increase of an oxygen overvoltage can improve the performance of recycle life

    對于電池性能衰減的原因，認為除了所使用的材料是影響電池性能的重要因素之外，在溫度和大電流作用下，電池的正負極材料發生裂解，極片內空隙增大，電池內阻性能惡化是引起電池高倍率循環性能惡化的關鍵;通過抑制正極析氧和膨脹，並降低負極合金材料的粉化過程，將有望緩解電池內阻特性的惡化，從而提高電池高倍率充放電循環性能。
  11. We calculate the stress fracture limit, critical index limit and melting limit in a high power double clad fiber laser. the results show that the average output power decreases when the temperature is too high. to maintain the pumping efficiency and the output power, some cooling methods should be used when the output power reaches a certain level

    給出了熱效應對雙包層光纖激光器影響的裂解極限、臨界折射率極限和熔化極限與光纖結構參數和泵浦功率的表達式，理論分析和數值模擬結果表明對于高功率的雙包層光纖激光器溫度很高時激光增益下降，在一定的功率水平上需要進行外界的冷卻，以保證泵浦激光的效率和高功率的激光輸出。
  12. The purpose of this paper is to present a numerical methodology for simulating the flow of shock tunnel. the numerical approach uses a maccormack scheme or s - w spiliter for the quasi - one - dimensional euler equation coupled with real gas effect. a simple method is used to track contact discontinuities

    採用maccormack格式及s - w分裂方法求解準一維euler方程，考慮高溫下分子的振動、氣體和壁面間的摩擦和傳熱，根據高壓段的氣體質量守恆的方法來跟蹤接觸間斷。
  13. The pyrolysis mechan ism functions of the second stage of dvb / hpso and vpso / hpso are both parabola principle, and the rates of pyrolysis reactions in this stage are both controlled by one - dimensional diffusion

    600時， ai可與先驅體裂解產生的含碳小分子氣體反應生成a14c3 ， 800時ai可與裂解氣氛nz反應生成ain ，溫度升高， al的氮化反應不斷進行。
  14. Insulating and sheathing materials of electric and optical cables - common test methods - methods specific to polyethylene and polypropylene compounds - tensile strength and elongation at break after conditioning at elevated temperature - wrapping test after conditioning at elevated temperature - wrapping test after thermal ageing in air - measurement of mass increase - long - term stability test - test method for copper - catalyzed oxidative degradation

    電纜和光纜的絕緣和護套材料.通用試驗方法.聚乙烯和聚丙烯化合物專用方法.高溫處理后抗拉強度和斷裂伸長度.高溫處理后的卷繞試驗.在空氣中熱老化后的卷繞試驗.質量增加的測量.長期穩定性試驗.催化銅氧化降解的試驗方法
  15. P / a, fl / py ratios and ring numbers of pahs were used to assess the origins of the pollutants, suggesting possible sources such as combustion of coal, wood and petroleum pyrolysis

    P / a 、 fl / py比值、 pahs環數以及烷基化pahs表明膠州灣表層沉積物中pahs幾乎全部由人類活動產生，來源為煤炭燃燒、木材燃燒、石油類高溫裂解及油類污染。
  16. If the materials are degraded in the event of high temperature and high shearing rate, the melt viscosity will decrease due to the breaking up of the molecular bonds

    如果材料因高溫或高剪切率加工而降解，熔膠粘度會因分子鏈斷裂而降低
  17. Abstract : based on the hypotheses of three - piece straightening curve. it isverified that the method for using little deformation condition was true with accurate solution of three - piece straightening curve. the mechanics behavior of slab was analyzed in regard to the creep properties of high temperature slab. the results show that the strain, the strain velocity and the stress varied so smoothly that the inner crack was prevented. technical renovation is carried on by adjusting the displacement of rolls and by using the accurate solution of three - piece straightening curve

    文摘:基於三段矯直曲線應變速率的假設，通過計算三段矯直曲線的精確解，驗證了使用小變形條件的正確性;考慮高溫鑄坯蠕變性能，對鑄坯的力學行為進行了分析，得出了使用三段矯直曲線方法，鑄坯應變速率、應力及應變在矯直區內變化較為平緩，可有效避免鑄坯內裂紋的形成;使用本文三段矯直曲線精確解，調整輥列位置，可進行連鑄機的在線技術改造。
  18. Characteristics : durabce, high temperature resisting, high voctage resisting, antisepsis and envicromentally protective. getting rid of poor factors ( non - cleaness, aging, unstasicity, disjoints and blow up ) caused by soft rubber joints

    具有：耐用、耐高溫、耐高壓、防腐、保護環境的優點，取代了橡膠軟接頭所帶來的不衛生、易老化、耐壓不穩定、易脫層撕裂、爆破等不良因素，解決了系統運行中的后顧之憂。
  19. Soot carbon is a filling agent for rubber that can improve its wear resistance. it is mainly produced by high temperature cracking that use coal tar as the feedstock

    炭黑是橡膠里的一種填充劑，可以增加橡膠的耐磨性等，它主要是以煤焦油為原料在高溫下裂解而成的。
  20. When diapir fractures opened, entering of hot fluid into reservoirs may cause dissolution of carbonate minerals, and when diapir fractures closed, carbonate minerals precipitated in high temperature condition

    底辟斷裂開啟時，深部富c02熱流體進入儲層，導致碳酸鹽礦物溶解；通道閉合時，高溫使碳酸鹽礦物沉澱。
分享友人
分享到 Line

分享到臉書