annealing texture 中文意思是什麼
annealing texture
解釋
退火織構-
Zircaloy - 4 sheet, which was cold - worked followed by recrystallization annealing, exhibits longer lcf life in the rolling direction than that in the transverse direction, and the fact that difference in lcf life between both directions becomes larger as the range of plastic strain becomes lower can be attributed to the texture effect, p - solution treatment deteriorates the alloy ' s lcf property because the treatment lowers the average value of alloy ' s schmid factors, and the subsequent annealing - treatment in a - phase range has a impact on the lcf properties, i. e. the subsequent annealing - treatment at 500 ? for 1. 5h results in better property than that at 750 for 1. 5h, which comes mainly from the fact that the alloy annealled at 500 for 1. 5h has lower amount of the precipitate particles than the alloy annealled at 750 for 1. 5h
對于冷加工后經再結晶退火處理的zr - 4合金，軋制方向的低周疲勞壽命比橫向要大。隨著_ p的降低，兩個方向的低周疲勞壽命的差別相應增加，這是由於合金中存在織構的緣故。冷加工后經再結晶退火處理的zr - 4合金在固溶處理后，抗疲勞性能明顯降低，這主要是由於固溶處理降低了合金的schmid因子；固溶處理后在相區的退火對疲勞性能有影響，即500 1 . 5h退火的抗疲勞性能要優於750 1 . 5h退火，這主要與500 1 . 5h退火的合金中沉澱相粒子的數量較少有關。 -
Effect of intermediate annealing on cubic texture of high - purity aluminum foils
中間退火對高純鋁箔立方織構的影響 -
Both the smco5 phase and the sm2co17 phase appear while the annealing temperature is higher than 700. the texture of the thin films is influenced by the annealing temperature remarkably
結果表明，在低於700的溫度退火時，主要是smco5永磁相析出，而在高於700的溫度退火時，薄膜中同時有smco5和sm2co17永磁相析出。 -
I. hc is greatly improved from several oe to nine thousands oe with the rise of annealing temprature, but mr / ms decreases, which mainly because fcc texture changes into fct texture
熱處理溫度在600 850的范圍內，隨著的溫度的升高剩磁比稍有降低，主要原因是晶相結構的形成和fcc相到fct相的轉變。 -
The effect of final annealing on cube texture of high - purity aluminum foils
成品退火對高純鋁箔立方織構的影響 -
The effect of middle annealing on cube texture of high - purity aluminum foils
中間退火對高純鋁箔立方織構的影響 -
The structure and texture of continuous or batch annealing deep drawing and extra - deep drawing steel sheets were observed and analyzed
摘要對連續退火或罩式退火后的深沖鋼板和超深沖鋼板的組織以及織構進行了觀測和分析。 -
The difference is mainly resulted from the original structure and texture inhomogeneity of hot rolled steel plates, and the process of heating and annealing can also have a great effect on the inhomogeneity of the surface and center grain sizes in the steel sheets
這種區別主要來源於熱軋鋼板原有組織和織構的不均勻性，退火加熱過程也會對鋼板表面和心部晶粒尺寸的不均勻性產生很大影響。
分享友人