mass balancing 中文意思是什麼
mass balancing
解釋
質量平衡-
In order to solve need badly three - ring type gear reducer ( problems of high vibration, high temperature and short spin arm bearing life in operation, by means of power separation flow, elastic ring equilibrating load, tardy down and assimilation vibration of synchronous belt transmission, and mechanism balance principle, the author designs a new type three - ring type gear reducer with arc tooth synchronous belt transmission, the gear reducer is fully balancing, equilibrating load and reducing vibration and phase difference 180 ( of mass eccentricity
為解決一般三環減速器振動大、溫升高和轉臂軸承使用壽命短等生產中迫切需要解決的問題，依據功率分流、彈性環均載、同步帶緩沖及吸振和機構平衡原理，設計出了一種具有圓弧齒同步帶傳動的完全平衡、均載減振，偏心相位差為180的新型三環減速器。 -
This paper firstly analyses the various reasons and dangers caused by unbalanced rotors according to information and experiments, after these, different balancing methods for different types of unbalancing rotors were discussed. on the basis of the theory that discussed above, the paper analyses different types methods of measuring especially wattmeter measuring system and character of signals of hard bearing dynamic balancing system and designs a hard - bearing microcomputer - based measuring system for different types of hard bearing dynamic balancing machines. using advanced technology both in hardware and software of the modern, this system aims to reach the general goal of great mass, high precision, easy - to - operate and lows cast
本文在文獻資料和實驗的基礎上，分析了轉子不平衡產生的原因及危害，論述了各類不平衡轉子的平衡方法，在此基礎上根據生產實踐的需要，以mcb - 980通用硬支承平衡機為基礎，以剛性轉子為研究對象，分析各種測量方法尤其是瓦特表測量系統的優缺點及力測量動平衡機系統的信號特點，建立了一種新的剛性轉子雙面動平衡的數學模型，分析了求取動不平衡量大小和相位的原理，在此基礎上開發了一種以工控機為主機的硬支承動平衡機微機化測量系統。 -
A virtual balancing method of a flexible rotor based on rotor dynamic and finite element method is proposed in this paper to decrease the vibrations caused by mass unbalancing
摘要為了有效地降低回轉機械由於質量不平衡引起的振動故障，基於轉子動力學理論和有限元數值分析方法，進行了柔性轉子系統虛擬動平衡研究。 -
The process of redistributing the mass ( weight ) more uniformly is balancing
改變轉子的質量分佈以使其相對于旋轉軸均勻分佈的過程稱為平衡。 -
Secondly, based on the defects of the uptodate balancing machine which were employed in the motorcycle manufacture plants, this dissertation has presented a new method on the means of checking unbalance mass of the motorcycle engine crank set. it has adopted the hard - bearing balancing machine as the prototype ， utilized tow group of resistance sensors placed in vertical direction with one another to pick up the information which stand for the inertial force of the motor engine crank set when it is running
其次，通過對當前國內外曲柄連桿機構動平衡實驗的現狀及其存在問題的分析研究，提出了一種新的測試方法：在工作原理上採用硬支承型測力式動平衡機，在測量方法上應用互成900的兩點測量來失量合成任意一點旋轉慣性力大小及方向，這也是也是其不同於以往試驗機的最大之處。 -
Secondly, based on the defects of the uptodate balancing machine which were employed in the motorcycle manufacture plants, this dissertation has presented a new method on the means of checking unbalance mass of the motorcycle single - cylinder engine crank - connecting rod mechanism. it has adopted the hard - bearing balancing machine as the prototype, utilized tow group of resistance sensors placed in vertical direction with one another to pick up the information which stand for the inertial force of the motor engine crank set when it is running
其次，通過對當前國內外曲柄連桿機構動平衡試驗的現狀及其存在問題的分析研究，提出了一種新的測試方法：在工作原理上採用硬支承型測力式動平衡機，在測量方法上應用互成90的兩點測量來矢量合成任意一點旋轉慣性力大小及方向，這也是其不同於以往試驗機的最大之處。 -
Furthermore, on the theoretics of the balancing machine and associations with the practicalities of the motorcycle crank, it has reasoned out the test principles and mathematic model of the unbalance mass checking device of the motorcycle engine crank set, which is supported by the new method
提出了新型試驗方法所採用試驗裝置的測試原理和數學模型，並設計出了模型機。模型機正在製造中。第三：得到了一個結論：摩托車發動機曲柄連桿機構的動平衡率等於旋轉不平衡量除以往復不平衡量。 -
The purpose of " balancing " - of restoring uniformity of mass distribution insofar as possible - is not to eliminate all rotating system unbalance, but to bring it down to a tolerable level
平衡（使轉子質量分佈均勻）的目的並不是完全消除轉子的不平衡，而是將其降低至容許范圍內。 -
Furthermore, the request and conformation of the unbalance mass checking software, which is applied into this balancing prototype machine, has been brought forward in this dissertation
第四，對測試過程中數據定標進行了詳細研究。對數據採集、數據處理作了簡要分析。 -
The design of automatic balancing system by mass removing based on lab windows cvi
車用開關性能測試系統的設計 -
Responsible for the assembly line efficiency and quality for normal mass production product, on site trouble shooting, responsible for continuous improvement on line including fixture / layout / sop / balancing
作為新產品項目的成員參與項目檢查，負責流水線布局，工裝夾具選擇及設計，標準操作程序準備以保持生產線效率和平衡設計，並負責操作培訓及進行運作指導。
分享友人