pneumatic engine 中文意思是什麼

pneumatic engine 解釋
氣壓機
  • pneumatic : adj 1 空氣的；似空氣的，氣體的；空氣學（上）的。2 【機械工程】壓縮空氣推動的；汽動的；風動的。3 ...
  • engine : n. 1. 機械，機器。2. 引擎，蒸汽機，發動機。3. 機車，車頭。4. 工具；〈古語〉方法，手段。vt. 給…安裝發動機。
  1. Characteristic and suitablescope the surface basic is 10 steeil and spcc, then sinter 20high - tin, the manufacture has good antifriction, no fever heat, against grip axes, suitable for engines camshaft and pneumatic engine, refrigerating machine bushes. at present, our factory is the greatest export factory for eccentric bushes in the domestic area, and match bushes to isuzus idler gear for japanese isuzu co

    表面以10鋼或spcc低碳鋼為基礎，表面燒結錫合金材料扎制而成，產品具有耐磨性能好，不發熱，不咬軸等優點，特別適用於發動機凸輪軸，氣壓機，製冷機軸套，目前我廠是國內出口偏心軸瓦的最大廠家，並一直為日本五鈴公司配套五十鈴惰輪襯套，和國內各主要柴油機廠配套。
  2. Valve, starter control, pneumatic, aircraft engine general specification for

    飛機燃氣渦輪發動機空氣起動機控制活門通用規范
  3. Chapter 3 is devoted to an introduction of structure and function of simulation system of pneumatic operation for marine engine, which was conducted by us, emphasizing its character of real - time online control & simulation

    接著在第三章將主要介紹自行研製的「船舶主機氣動操作實時模擬系統」的結構組成和功能；著重強調其所具有的實時在線模擬特點。
  4. As we know, pneumatic operation system for marine engine is an important component of the marine engine controlling system. without being manipulated properly and adroitly or failing to resolve relevant faults in time, the normal running of the shipping will be endangered

    眾所周之，船舶主機氣動操作模擬系統是主機控制系統中的一個重要的組成部分，如未能正確熟練地對其進行操作或及時地排除相關故障將直接影響到船舶的運行安全。
  5. The paper focused on this task and covered these contents : realizing the real - time, online and dynamic simulation of the pneumatic operation system for marine main engine on the basis of analyzing the pneumatic devices " principle and by the means of multimedia technology ; describing dynamically the flowing direction of the controlling pneumatic line according to its logical relations in the three working conditions - starting, stopping and reversing

    本文圍繞此課題主要完成以下內容：在對manb & w主機氣動裝置原理分析基礎上，運用計算機多媒體技術，實現船舶主機氣動控制系統的實時、在線、動態模擬。針對主機的起動、停車、換向三種操作工況，依據氣路邏輯關系動態地描述了控制氣路的流向。
  6. As a rule, when engineer wants to change over the pneumatic manoeuvring system to the mechanical manoeuvring system or vice versa, the engineer must perform the change - over operation with the engine stopped

    作為一個慣例，當輪機員要轉換氣動操縱系統到機械操縱系統或反過來轉換機械操縱系統到氣動操縱系統，輪機員必須在機器停止時進行轉換操作。
  7. The rigs indlude special carrier ( developed by our company ), engine, hydraulic transmission, right angle gearbox, single ( double ) drum drawwork, rotary table transmission box, hydraulic drawworks, front and rear supporting frame, double - section hydraulic telescopic mast, crownblock, travelling hool, weight indicator, hydraulic, pneumatic and electrical system, etc

    專用底盤為載車，由專用汽車底盤、發動機、液力變速箱、角傳動箱、單（雙）滾筒絞車、轉盤傳動箱、液壓絞車、前支架、后支架、雙節液壓伸縮式井架、天車、游車大鉤、指重表、液壓系統、氣路系統、電器系統等組成。
  8. When you want to manoeuvre the main engine by the pneumatic manoeuvring system, it is necessary to turn the handle to the “ normal ” position

    當你想要通過氣動操縱系統操縱主機時，必須轉動手柄到正常位置。
  9. The dissertation is outlined below. firstly the construction of man b & w marine engine control system is briefly introduced. specifically, construction & logical relationship of the b & w pneumatic control equipment and hardware construction & the speed - regulating principle of dgs - 8800 - the digital governor device are analyzed

    本文的主要組織框架為：首先大概介紹了manb & w主機控制系統結構，具體分析了阻w氣動控制裝置結構組成和邏輯關系以及dgs 8800電子調速裝置硬體結構組成和調速原理。
  10. According to the feature of low atmospheric pressure and thin air in plateau area, on the basis of the relative coat increase, the specific property of small agricultural internal - combustion engine ' s combustibility are analysed, the aim is to increase pneumatic efficiency, improve combustibility

    摘要結合高原地區大氣壓低，空氣稀薄的特點，在成本相對不增加的基礎上、對小型農用內燃機燃燒狀況的特性進行分析，其目的在於提高充氣效率，改善燃燒狀況。
  11. If by their ticket enforcement agencies use the power, control valves can be divided into pneumatic, electrical, fluid movement three, namely to compressed air to power sources pneumatic - valve to call for the engine electric control valves for the liquid medium ( such as oil ) pressure - driven electricity fluid moving control valves, and their functions and characteristics hours are electromagnetic valves, electronic style, smart, floor bus - control valves

    如果按其所配執行機構使用的動力，控制閥可以分為氣動、電動、液動三種，即以壓縮空氣為動力源的氣動調節閥，以電為動力源的電動控制閥，以液體介質（如油等）壓力為動力的電液動控制閥，另外，按其功能和特性分，還有電磁閥、電子式、智能式、現場總線型控制閥等。
分享友人
分享到 Line

分享到臉書