processing step 中文意思是什麼
-
In this dissertation, al - si / sicp composites brake rotor with diameter of 1200mm was firstly fabricated by a novel spray deposition technology, and simultaneously coupled brake pad was prepared by a novel dry - powder processing route, termed as two - step pressing process. a wedge pressing technology was developed to densify the as - produce al - si / sicp composite brake rotor
本文首次採用噴射沉積技術制備了直徑達1200mm的al - si / sicp制動盤，同時採用二次壓制工藝制備出了配套的合成閘片，研究了制動盤的楔壓緻密化技術、機理，復合材料摩擦磨損性能及機理。 -
As an advanced materials preparation technology, spray - deposition has shown remarkable superiority in producing large - sized alloys and metal matrix composites. however, the spray deposeted preforms usually contain a certain quantity of porosity. besides, the oxide films on the surface of the particles lead to week metallurgic conjunction between the particles. in order to obtain an ideal structure and performance, the porous preforms need further densifying and plastical forming. in this paper, a new technology named wedge pressing was used to densify spray - deposeted 5a06 aluminium alloy, in which the large deformation can be obtained through the sum - up of local deformation and multi - step small deformation. this method can also solved the problems in traditional processing and greatly decreased the producing cost. what ’ s more, the reserch on the wedge pressing desification rules about the large - sized spray deposeted preforms was significant it was vital not only to the further densification of the prefoums but also to the further research on plastical deforming the research was also benefit to the industrialization an the application of the spray deposeted porous materials
坩堝移動式噴射沉積技術作為一種先進的材料制備新技術，在制備大尺寸合金及金屬基復合材料方面具有顯著的優越性。然而噴射沉積坯件特別是大型坯件通常存在一定量的孔隙，顆粒表面存在一定量的氧化膜，顆粒之間未能完全達到良好的冶金結合狀態，因此需要進行后續緻密化和塑性變形才能獲得理想的組織和性能。本文採用一種新型的楔形壓制工藝，即通過局部變形、多道次小變形累積實現大變形的緻密化加工方法，對噴射沉積多孔坯料進行后續緻密化和塑性變形，很好地解決了傳統加工工藝的難題，大大降低了生產成本。 -
After processing, the sensitometrically exposed step wedge is read on a densitometer and the data is plotted.
加工完畢后，即用密度計對試驗膠上復制的階梯級譜的密度進行測定，然後用測得的數據作圖。 -
Because color isochromatic fringes appear in the stress model based on a plane polariscope in white light, we studied the problems systematically by a digital camera as image inputting device, digital image processing technique and bp artificial neural network. based on the work that has been reported before, a technique named five - step color phase shifting technique ( fcpst ) to acquire single isoclinics is presented
根據白光入射時應力模型在偏振儀光學系統中的等色線條紋是彩色的特點，本論文採用彩色數碼相機作為數據採集與輸入設備，結合彩色信息圖像處理和bp神經網路等新技術，對上述兩個難題進行了系統的研究，獲得以下成果：在綜合前人工作的基礎上，提出獲得全場單純的等傾角相圖的五步彩色相移法。 -
( 3 ) by exploring the filming processes of the pedt negative pole, this paper, creatively using the vacuum single step method, has found a comparatively suitable processing condition
（ 3 ）通過對pedt陰極被膜工藝過程的研究，找到了較適合的單體m和氧化劑c配比，清洗液的配方和清洗時間，烘乾溫度和時間，被膜和補形成次數等工藝參數。 -
Thickening is the usual first step in sludge disposal processing.
污泥處置過程中，濃縮通常是第一道工序。 -
In this system, the movement of the step - electromotor is controlled by computer, and then the dial pointer is drove by the step - electromotor. at the same time, these images of the analog instrument are took by high precision ccd video, and then these images will be processed by the computer, using some image - processing algorithms such as image segmentations, threshold identification, image binarization, areas labeling, dial center - point identification, useful areas identification & abstracting, and areas thinning, etc. followed this, the dial pointer of the “ circle ” is able to be located. at last, the dial pointer position will be recognized by the computer
本系統由計算機控制步進電動機的運動，進而驅動指針式儀表表針的運動，並且通過高精度ccd攝像機實時獲取表盤圖像數據，同時進行表盤圖像的相關處理，包括圖像分割，閾值確定，圖像二值化，區域標記演算法，圓心擬合，有效區域識別提取，區域細化等，最終快速識別出表盤指針所處位置;最後，根據國家指針式儀表類檢定規程所制定的演算法計算出該儀表的相關誤差，檢定指針式儀表的各種精度，通過這些數據判斷該儀表是否合格，列印該儀表的檢定結果報表。 -
Assembly processing step
組合加工步驟 -
The analytical approaches involved in the dissertation includes cross section analysis 、 time series regression 、 step by step regression and contrast analysis, the following technologies also are applied, including computerizing lower partial moments ( lpm ) with matlab, processing revenue data with excel, regression analysis with eviews
主要運用橫截面分析、時間序列回歸、逐步回歸和對比分析方法，還用到matlab編程計算下偏矩風險值， excel處理收益數據， eviews回歸分析。 -
In this paper, the drive theory of the large ratio friction transmission is studied ; a new type elliptical cam wave generator is designed ; the large ratio friction transmission prototype is designed and manufactured ; based on the ansys finite element method software, structure of the elliptical cam is analyzed ; precision index of the manufactured large ratio friction transmission prototype, such as transmission accuracy, least step, stability of the least step, load capacity is measured by the absolute rotary encoder. by analyzing the measurement data and research content, it is think that the new elliptical cam wave generator could overcome a good many problems brought by processing errors, facilitate size precision adjustments, input moment can be achieved in the form of a pure force couple importing ; through this study, " the large ratio friction transmission prototype " could apply in practical engineering basically
本文研究了大速比摩擦傳動的傳動理論;設計了新型橢圓凸輪波發生器，設計製作了大速比摩擦傳動樣機;用軟體ansys對所設計的橢圓凸輪結構進行了有限元分析;用19位絕對式編碼器測試了大速比摩擦傳動機構的傳動精度、最小步距、最小步距的穩定性以及帶負載能力等各項精度指標;對測量數據和研究內容進行了歸納和整理，認為新型橢圓凸輪波發生器克服了加工誤差帶來的諸多問題，新型橢圓凸輪波發生器可以進行尺寸精度調整，能夠達到輸入力矩以純力偶的形式輸入;通過本項研究，基本可以使「大速比摩擦傳動機構」在工程中得以應用。 -
Abstract : thermally induced stress and the relevant warpage cause by inappropriate mold design and processing conditions are problems that confounded the overall success of injection molding. a thermorheologically simple thermoviscoelastic two - dimension material model is used to simulate the residual stress and warpage within injection molded parts generated during the cooling stage of the injection molding cycle. the initial temperature field corresponds to the end of the filling stage. the fully time - dependent algorithm is based on the calculation of the elastic response at every time step. numerical results are discussed with respect to temperature and pressure
文摘:不均勻的熱殘余應力及其變形是注塑成型加工中常見的工程問題之一.應用熱流變簡單材料的二維熱粘彈本構方程得到的遞推公式，數值模擬了成型中的熱殘余應力及其翹曲變形，並用數值實驗討論了溫度、壓力對注塑件殘余應力及變形的影響，發現溫度變化不均勻是注塑件翹曲變形的最主要原因，其影響遠大於壓力的作用，與工程實驗的結論一致 -
With the intelligentization of wireless devices, a large quantity of them have been provided with the ability of data processing, simultaneity the number of the people who have wireless intelligent device is on the increase. it makes the mobile commerce to spring up. more and more enterprise information systems extend to support mobile devices to access step by step
無線設備智能化，相當數量的無線設備已經具備數據處理的能力，同時人們對智能移動設備的擁有率在不斷地提高，種種條件促進了移動電子商務的興起，各種企業的信息系統也正逐漸拓展到支持移動設備的接入訪問。 -
Based on the analysis and processing of the digital speckle pattern, the translation and rotation invariant features are discovered, and a one - step feed - forward neural network is creatively proposed which makes it possible to realize the intelligent recognition of interface defects
通過對數學散斑條紋的分析與處理，找出了能代表條紋信息的移位不變與旋轉不變特徵值? ?最大斜率，進而構造一種新的網路模型，即單步前饋式三層網路系統.率先實現了把神經網路系統用在數字散斑無損檢測之中，完成了神經網路系統對粘接界面缺陷的智能辨識 -
This paper has introduced the design of the instruction mechanical system, servo control system and image collection and processing system of the automatic tester for dial gauges in detail. it is illuminated that the step motor with the card of i / o and the step motor actuator is driven by computer. the step motor drives the surveying rod of automatic tester for dial gauges through the transfer machinery and realizes micro - displacement of the surveying rod
本文詳細介紹了指示表自動檢定儀的機械繫統、伺服控制系統、圖像採集與處理系統的設計，闡明系統是在計算機的控制下，由計算擬通過i o卡、步進電機驅動器，驅動步進電動機，由步進電動機通過傳動機構推動被檢指示表的測桿移動，從而實現測桿的微量進給。 -
As the character segmentation and recognition are doing synchronous, the wrong segmentation can be put right. and this permits the use of a lexicon directly within the lb algorithm rather than as a post - processing step
由於lbdtw演算法將字元分割識別同步進行，字元分割是基於上一層字元識別結果的，分割錯誤可以根據識別信息得到糾正，並且統計語言信息可以融合到lb演算法分層之間進行優化搜索。 -
Facing the problem that we always ask ourselves whether the technique and parmeters we use are suitable, we have to consider it in five main processing step, deconvolution, static correction, normal moveout, noise attenuation and migration
根據噪音在處理過程中的不同階段表現屬性不同，處理中採用不同的處理手段或不同的處理參數分階段對噪音進行衰減。以便做到最大限度壓制噪音，而盡可能不損傷有效信號，提高原始資料的信噪比。 -
Geometric distortion is traditionally corrected by an image resampling operation which is applied as a post - processing step to pfa. the scene size limits of pfa presented by range curvature qpe, can be alleviated by using an efficient image domain space - vairant post - filter
通常採用圖像域插值的方法校正幾何失真，而利用空變濾波器使散焦的點重新聚焦，這些校正方法可以減輕距離彎曲對成像范圍的限制。 -
However, this document requires a separate xinclude processing step
不過，該文檔需要單獨的xinclude處理步驟。 -
Controls and the page itself also raise life - cycle events at each processing step, such as
控制項和頁本身還會在每個處理步驟引發生命周期事件，例如 -
The main sources of uncertainty come from non - linear calibration models and pre - processing step of samples
測量誤差的主要來源是樣品校正曲線擬合誤差、樣品測定重復性標準偏差。
分享友人