reactive sintering 中文意思是什麼

reactive sintering 解釋
反應燒結
  • reactive : adj. 1. 反動的，倒退的，復古的。2. 反應的；反作用的；反沖的；【電學】電抗的；【化學】反應性的，活性的。reactivity n. adv. -ly ,-ness n.
  1. The expansion and dehiscence behavior during the vacuum reactive sintering below 660 of compact ti / al composite powders was experimentally investigated, and the reasons of expansion and dehiscence were theoretically analyzed. the method of low temperature reactive sintering was generalized, and the experiment testified the method effective. the rule of the expansion of the billets was generalized from the result of density of the billets

    低溫反應燒結工藝:研究了高能球磨ti / al復合粉體在溫度低於660下真空無壓反應燒結過程中的膨脹和開裂行為，分析了產生膨脹和開裂的主要原因;並提出了能夠有效預防坯料開裂的方法;通過測定坯料在低溫燒結后的密度，總結了其體積膨脹的規律;通過x射線衍射技術分析了隨球磨時間不同，金屬間化合物的生成情況。
  2. Abstract : in this paper, the workmanship of reactive sintering of thermal spray coating, microstructure and bonding property are introduced

    文摘:介紹了熱噴塗層的中溫反應燒結工藝，及其組織結構的特點和塗層結合性能。
  3. The main conclusions are as follows : ( 1 ) o ' - sialon / sic has been prepared by reactive sintering techniques

    得出如下結論： （ 1 ）以si粉、粘土和sic粉為原料，採用反應燒結工藝低成本制備了力學性能優良的o ' - sialon sic陶瓷材料。
  4. This paper is concentrated on preparing si3n4 / sic, si2n2o / sic and o ' - sialon / sic by reactive sintering techniques. the components of raw materials and microstructure of these three ceramics were studied. at the same time, molten al, cu, zn, mg and cryolite corrosion resistance of silicon nitride bonded silicon carbide were tested too

    本論文通過成份及微結構設計，採用反應燒結工藝制備了力學和抗氧化性能優異的o ' - sialon sic 、 si _ 2n _ 2o sic和si _ 3n _ 4 sic陶瓷材料，並研究了它們的抗鋁、銅、鋅、鎂有色金屬熔體及冰晶石熔鹽侵蝕性能。
  5. Tic, zrc and cu - 50 % tic were fabricated by reactive ball milling using ti, zr, c and cu powders for raw materials. compound powders were prepared by ball - milling with raw powders that have been fabricated. dispersion strengthen cu - based materials was synthesized at last though a set of technical course that consist of different pressing technique, sintering technique and heat extrusion technique

    本課題以單質ti 、 zr 、 c和cu粉末為原料，用反應球磨技術制備了tic 、 zrc和cu - 50 tic原料粉末，將制備的原料粉末和cu粉用球磨混合，制備出cu - tic 、 cu - zrc和cu - （ tic + zrc ）復合粉末，然後設計不同的壓制工藝和燒結工藝進行壓制、燒結和熱擠壓，最終獲得高強度的彌散強化銅基復合材料。
  6. Study on the effect of magnesia to ztm by reactive sintering in situ

    對原位燒結含鋯莫來石材料性能影響的研究
  7. Therefore, a new technology, which consists of the mechanical milling ( mm ), reactive sintering and hot hydrostatic extrusion has been put forward

    本文採用機械球磨?反應燒結?熱靜液擠壓方法，有望成為制備高性能ti - al基合金的有效途徑。
  8. The material of the experiment is compact ti / al composite powders prepared by high energy ball milling. the compact ti / al composite needs reactive sintering at low temperature and high temperature, in order to get high densified tial alloy

    本文實驗方法是，球磨不同時間的ti / al復合粉，然後在一定壓力下冷壓或者300 400下熱壓制坯。
分享友人
分享到 Line

分享到臉書