slave computer 中文意思是什麼

slave computer 解釋
從計算機
  • slave : n 1 奴隸。2 …的奴隸，耽迷於…的人 （of; to）。3 奴隸一般工作的人，苦工。4 【動物；動物學】奴隸蟻 ...
  • computer : n. 1. 計算者。2. （電子）計算機；計量器。-ism 電子計算機主義〈認為電子計算機萬能等〉。-erite, -nik 計算機專家；計算機工作者。
  1. When testing begins, the computer of the tested uav flight control system will be connected into the network as a slave. the master of the system will diagnose faults should there be any ; otherwise it will set flight parameters and load flight course data for the slave

    檢測時，無人機的飛控系統計算機作為從機連入網路，如果從機的飛控系統沒有故障，主機將為從機設置飛行參數和裝定航線數據；如果有故障，則主機為從機飛控系統診斷故障。
  2. The development of fieldbus technology made lonworks field bus outstanding in all kinds of fieldbus. this paper simply introduces some kinds of common using fieldbus and the important position and influence of lonworks fieldbus in all kinds of fieldbus, carefully describes the technology core of lonworks technology, puts great emphasis on the introduction of the development and design of public security node of intelligent district which adopts computer, communication and control technology, carefully designs the interfaces of hardware circuits. the public security node of intelligent adopts 8031 single chip as its main processor to complete the application program of user, which mainly collects, process and control all kinds of field signal, and neuron chip 3150 as its slave processor to communicate with other nodes on field network, which works under parrel slave a mode

    現場總線技術的發展使得lonworks技術脫穎而出，本文簡要介紹了常用的幾種現場總線的概況以及lonworks技術在現場總線技術中的地位和影響，對lonworks技術的技術核心：神經元晶元、 lontalk協議、 lonworks收發器、 lonbuilder及nodebuilder進行詳盡的描述；重點介紹了集先進的計算機技術、通信技術、控制技術為一體的智能小區安防節點的開發與研製，對節點硬體電路的各種介面進行了詳盡的設計。本文設計的智能小區安防節點採用單片機8031作為主處理器來完成用戶的應用程序，主要負責對各種現場信號進行採集、處理及控制，工作在并行從a方式下的神經元晶元mc3150作為從處理器，主要完成與現場網路上的各節點及中心控制室之間的通信工作。
  3. 3 ide trough can connect dvd - rom that kind that compatible computer spend and hard disk at the same time, the hard disk is set as slave. operate switching over with the remote controller while using

    3個ide槽可同時接dvd - rom兼容電腦上用的那種及硬盤，硬盤設為slave .使用時用遙控器操作切換。
  4. Slave computer knows master computer with some trouble when the communication assumption between master computer and slave computer has changed. then control circuit will be automatically switched to slave computer, slave computer will take place of the task of master computer and inform some related person to deal with the trouble in order to resume the normal work. man - machine conversation windows of the control system adopted visual basic 6. 0 to design

    上、下位機之間的通訊採用串列通訊的方式，上位機正常情況下負責實時運行，當上位機遇到故障時，上、下位機之間的通訊約定會發生變化，這樣下位機就會知道上位機有故障，控制運行電路切換到下位機系統運行，下位機通過撥號系統通知有關人員，及時處理故障，以使上位機盡快恢復運行。
  5. Instead, the prototype had only a small command cabin with slave - rigged computer systems to control the superlaser and drive units

    取而代之的只是一個小的指揮艙和一部用於控制超級激光和驅動單元的從屬電腦系統。
  6. The whole system is made up of 3 modules, they are serial communication module, embedded web server module and the remote operation interface module. serial communication module which is designed referring to modbus realize the communication between host computer ( embedded linux system ) and slave devices ( soot - measuration instruments )

    串列通信模塊主要實現主機（嵌入式linux系統設備）與從機（煙道粉塵測定儀）之間的串列通信，參考國際上流行的modbus協議設計了系統的串列通信協議，使系統更具開放性。
  7. The automation is composed of two operating station computers ( one is a backup computer ) and three slave computers

    該自動化系統由兩臺操作站計算機（其中一臺備用）和三臺下位機組成。
  8. In this system, as master computer, pc can get signal that is send by slave computer, and by using pc, value of environment can be typed and inquired about

    在該系統中， pc機作為上位機，它可以接受下位機系統傳輸過來的信號，並可以通過它列印和查詢下位機發送來的環境測量值。
  9. The automation is composed of two operating station computers ( one is a backup computer ) and three slave computers. every slave computer, which is cored by omron c200 plc, controls a generator independently. slave computers have data detection and control function with the help of the data detection and control interfaces which are composed of all kinds of position swiches, sensors and execution units

    本自動化系統由兩個主站（其中一個是備用站）和三個子站組成，每個子站由一臺omronc200hplc構成，獨立控制一臺發電機。
  10. This dissertation mainly introduces a host - slave system of a three coordinates printed circuit board numerical control drilling and milling machine. control instructions and parameter have been delivered by the master computer to slave computer dependently and smoothly in order to guarantee the work that can be accurately and promptly done. besides, the host computer collects various kinds of state signals that the slave computer feedbacks, then diagnoses and deals with them

    本課題研究開發了一個三坐標印刷電路板數控鉆銑床主從式控制系統，可使上位機能夠可靠、暢通地將經過處理的控制指令和參數發送到下位機，保證下位機能夠準確、及時的工作，同時，上位機收集下位機反饋的各種狀態信號，進行診斷和處理。
  11. Master computer and slave computer perform the control system task together

    改造的控制系統採用上、下位機的控制方式。
  12. Master slave computer

    主從式計算機
  13. Every slave computer, which is cored by 80c51 single chip microcomputer, controls a generator independently

    下位機以8051單片機為核心，每臺下位機獨立地控制一臺發電機組。
  14. Based upon single chip microcomputer of pic series, each module of communication of slave computer is structured

    同時，以pic系列單片機為核心，構建了各個下位機的通信模塊。
  15. The slave computer is pmac. dpram, servo motors, a / d conversion board, 3d analogue probe, i / o board are chosen in this system

    同時系統中擴展了dpram 、伺服電機、 a d轉換器、三維模擬仿形儀、 i o介面板。
  16. Slave computer ( measurement and control unit ) and master computer ( monitoring and management unit ) are connected by serial communication for data exchanging

    通過串列通信將下位機（測控單元）和上位機（監控管理單元）連接在一起，實現數據交換。
  17. ( 3 ) we designed the hardware circuit and programmed in supervise computer and slave computer respectively, which can control joint to act effectively

    （ 3 ）設計了相應的硬體電路並分別在上位機和下位機上用軟體編程，對關節的轉動進行有效的控制。
  18. Except that, many problem can " t be solved, such as the conflict of ccd " s high resolving power and big vision field, how to control the automatic gathering of pcb " s image using master and slave computer parallel structure, how to inspect the defect of pcb such as width of circuit, distance of circuit, losing circuit and so on. the research aim at how to combine computer vision, precise machine, automatic control with image process, at how to resolve the contradiction between high resolving power of image gathering and wide vision field, at how to realize automatic mosaic of image, at how to realize precise orientation of two dimension worktable, at how to realize communication between master computer and slave computer, and at how to inspect the defect of line width, line distance and losing

    除此以外，還有ccd高解析度和大視場之間的矛盾，上下位微機并行系統如何控制印刷電路板圖像自動採集，印刷電路板的線寬、線距和丟失線條等缺陷如何檢測等問題還懸而未決，本課題將就如何結合計算機視覺技術、精密機械技術、自動控制技術和圖像處理技術，如何解決圖像採集高解析度與大視場之間的矛盾，如何實現圖像的自動拼接，如何實現兩維工作臺的精確定位，如何實現上下位機的準確通訊，如何檢測線寬、線距缺陷和丟失線條等問題展開重點研究。
  19. Master computer can realize such function as real - time running, monitoring, setting quality parameters, communication with slave computer, alarm and real - time printing by inserting appropriate function card of according to bus protocol of pc and software

    上位機採用pc機的總線技術和插卡技術實現實時運行、監控、設定性能試驗的參數、通訊、報警以及實時列印。
  20. The article analyzes the development schemes of the host computer interface card, the adapter principle of the printer and reasons of selecting it. having studied signals of printer ports further, thus i determined the communication mode between the host computer and the slave computer, and designed communication circuit. the question of programming has been discussed

    論文分析了上位機計算機介面卡的開發方案，并行印表機介面原理和選用它的原因，研究了印表機埠信號，決定了通信聯絡方式，設計出上位機通訊硬體電路，並研究了上位機編程問題。
分享友人
分享到 Line

分享到臉書