控制淬火 的英文怎麼說

中文拼音 [kòngzhìcuìhuǒ]
控制淬火 英文
controlled quenching
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously

    應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。
  2. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  3. Gear flame or induction hardening process and its quality control

    齒輪火焰及感應淬火工藝及其質量控制
  4. It now possesses of not only some production equipment advanced in the national level, such as automatic hydraulic pressure spring eye machines, automatic control quenching furnaces and automatic control tempering furnaces the control accuracy attains 5 and shot blasting machines of landscape and vertical orientation, but also some sophisticated quality detection equipment, such as durometers, metallographic microscopes, stiffness and endurance test machines, etc. besides the hardware equipment, the company has a group of senior specialized technical personnel in the field of the design of the leaf spring processing, the leaf heat treatment as well as the tqc total quality control

    擁有自動液壓卷耳機自動控溫的淬火爐和回火爐爐溫控制精度達到5橫向和縱向噴丸機等國內先進的生產設備。同時還有為保證質量購置的硬度計金相顯微鏡剛度檢測及疲勞試驗機等先進的質量檢驗設備。從產品生產開始的每一個環節進行全方位的質量控制。
  5. Employing abrasive machining for the form of the gear and intellective - control carburizing and quenching technology for the surface, the gear is with high intensity, strong tenacity and wearability

    齒輪齒形採用磨齒加工，齒面採用智能控制滲碳淬火技術，齒輪的強度高、韌性和耐磨性好。
  6. Control and determination of retained austenite content in carburized and quenched alloy structural steels

    合金結構鋼滲碳淬火后滲層殘余奧氏體的控制
  7. From an examination of the tensile behavior of cz ly12 alloys under different temperature and strain rate, two kinds of deformation and intergranular fracture behaviors were observed that were opposite to the characteristic strain rate range in fine - grained superplasticity. the mechanisms are described as follows. the high ductility achieved at high strain rate is generally attributed to the dominant role of gbs accommodating mechanisms, which is considered as dislocation creep within grains controlled by subgrains

    研究選用自然時效淬火態的ly12鋁合金，進行了一系列不同溫度和應變速率下的單軸拉伸試驗， 480下，觀察到與傳統細晶超塑性特徵區間相反的行為：較高應變速率下，動態再結晶使晶粒細化，促進了晶界滑移，亞晶界控制的晶內位錯蠕變是晶界滑移的主要協調機制。
  8. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
  9. Correct control of the tempering temperature of quench steel

    淬火鋼回火溫度的正確控制
分享友人
分享到 Line

分享到臉書