擺動凸輪 的英文怎麼說

中文拼音 [bǎidòngtūlún]
擺動凸輪 英文
oscillating cam
  • 擺 : Ⅰ動詞1 （安放; 排列） put; arrange; set in order 2 （顯示; 炫耀） display; show off; put on; assu...
  • 凸 : Ⅰ動詞（高出） bulge; protrude Ⅱ形容詞（高於周圍） protruding; raised
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 擺動 : 1 （搖擺） swing; sway; oscillate; pendulate; waggle; wobble; vibrate; wiggle 2 [機械工程] jiggin...
  1. Discussinng the synthesis of cam - five linked mechanism for the given locus, and giving the detailed formulas by an example

    摘要對實現預定軌跡的擺動從動件盤形凸輪五桿機構的設計進行探討，並通過實例給出具體的解析設計公式和步驟。
  2. Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism

    摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。
  3. On the basis of the known actual contour equation of cam in the disk typed cam mechanism with swinging oblique bottomed follower, this paper expounded another method for determining inversely the track equation of cutter center and the motion law of follower, and three key techniques in numerical inverse seeking were solved successfully by adopting the method of curve matching

    摘要根據已知擺動斜底從動件盤狀凸輪機構的凸輪實際廓線方程，闡述了反求確定刀具中心軌跡方程和從動件運動規律的另一種方法，並採用曲線擬合等方法成功地解決了數值反求中的3個關鍵技術。
  4. This paper provides the general equations of the theoretical contour line and the actual contour line of roller translation follower and roller oscillating follower disc cam in the polar coordinates system and the rectangular coordinates system, respectively. the equations are not only fit for the different layouts of the relative position of follower and cam, but also fit for the different types of cam contour

    分別給出了滾子直動從動件和滾子擺動從動件盤形凸輪的理論廓線及實際廓線在極坐標系與直角坐標系下的通用方程，它們對于從動件與凸輪相對位置的不同布局方式及凸輪輪廓的不同類型均適用
  5. Abstract : the paper shows the relative deformation function of the cam mechanism with a roller follower as a linear time - invariant system, and gives the detail about the response limitation for the dynamic design and modification of cam mechanisms. an example demonstrates this approach can improve the flexible cam mechanisms

    文摘:以滾子從動件平面凸輪機構為分析對象，提出了相對變形函數這一新概念，並從理論上對其進行了研究，最後藉助於一凸輪機構在不同參數下其擺臂最大相對變形量的數值計算過程與結果，闡述了基於該理論的凸輪機構動態設計與修改的具體實現步驟與方法。
  6. The polar coordinates of tool swinging pivot are figured out, and the expressions of tool swinging and the variable - speed of spindle are derived

    通過對凸輪車削的運動關系進行分析計算，推導出在恆角度與恆速度切削的情況下，刀具擺角、機床主軸轉速與凸輪轉角位置的關系，為在實際中應用提供了理論依據。
  7. To keep constant cutting angle and speed, a method with tool swinging and variable - speed of spindle is presented

    為了解決上述問題，本文提出了刀具擺動與主軸變轉速的凸輪車削加工方法，以實現恆角度與恆速度切削。
  8. This paper points out that the traditional design method about the disc cam mechanism with oscillating follower has some shortcomings, thus it proposes one new method - using the differential method and the optimum technology to get the best parameters of the disc cam mechanism with oscillating follower

    摘要指出了傳統設計方法在確定擺動從動件盤形凸輪機構設計參數時的諸多不足，提出了一種新方法採用微分法和最優化技術聯合求解擺動從動件盤形凸輪機構的最佳設計參數。
  9. Taking the meshing theory of conjugate curved surface as a foundation, utilizing array method of rotation transformation of vector, the meshing equation and contour surface equation of conical cam mechanism with swinging conical roller follower were analyzed and derived, and the calculation formula of pressure angle and synthetic curvature of the mechanism was presented, thus laid a solid theoretical foundation for enhancing the machining accuracy of conical cam, improving its processing method and achieved the integration of cam cad / cam

    摘要以共軛曲面嚙合理論為基礎，運用矢量的旋轉變換矩陣法，分析並推導了圓錐滾子擺動從動件圓錐凸輪機構的嚙合方程和廓面方程，並給出了機構的壓力角和綜合曲率的計算公式，為圓錐凸輪加工精度的提高，改進其加工方法，實現凸輪cad / cam一體化奠定了堅實的理論基礎。
  10. This machine is newly researched and designed by our factory based on the model of combined cam, it winds up the plastic tape by the back and forth movement of the swinging stem driven by the cam

    採用心型凸輪的旋轉來帶動擺桿作來回移動而卷繞成形。比原往復絲桿的結構運轉更加輕松
  11. The interference discriminant and calculation method of a kind of cam mechanism

    一種擺動凸輪機構的干涉判別模型與演算法
  12. Cam with oscillating follower

    擺動從動件凸輪機構
  13. Cam with oscillating fo

    擺動從動件凸輪機構
  14. Finally taking a cam mechanism with oscillating follower as an example the construc tion method of adaptive system has been explained

    最後以擺動從動件凸輪機構為例闡釋自適應系統的構造方法。
分享友人
分享到 Line

分享到臉書