晶坯 的英文怎麼說

中文拼音 [jīngpī]
晶坯 英文
incipient crystal
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 坯 : 名詞1 （未經燒制的磚、瓦、瓷等的製品） base 2 （土坯） unburnt brick; earthen brick; adobe 3 [方...
  1. Control on continuous casting thin slab surface quality of peritectic steel

    包晶鋼連鑄板坯表面質量的控制
  2. W - cu composites prepared from the precipitation w - cu powder have higher sintered density, better mechanical and physical property, more homogeneous and finer microstructure than those prepared from w - cu powder by the balling - reduction method. in chapter 5, a combination of homogeneous precipitation and ball - milling process, namely the mechano - thermochemical process was employed to prepare ultra - fine w - cu powder

    其中，球磨w一cu復合粉（ hp一m ）壓坯在1150下燒結30min后，可獲得相對密度大於99 %的幾乎全緻密的超細晶粒w一cu復合材料， w的顆粒度小於0 . 5林m 。
  3. Molten steel level in mould of continuous cast process and casting speed can directly effect temperature of molten steel in mould

    摘要結晶器液位和鑄坯拉速可直接影響結晶器內鋼液溫度。
  4. When heating temperature reached 300, crackings appeared on the surface of ceramic tiles but the microstructure of glaze exhibited no apparent change when heating temperature reached 900, the glaze melted, the crystal structure of the tiles broke down, the integrity of ceramic tile was destroyed and the intensity was almost lost

    當溫度達到300 ，冷卻試驗時，釉面可產生裂紋，但顯微結構基本無變化；當溫度達到900 ，冷卻試驗時，釉面出現熔化現象，坯體晶體結構酥裂、破碎，完整性遭到破壞，強度基本喪失。
  5. Influential factors of primary dendritic arm spacing in high - carbon steel billets

    高碳鋼小方坯的一次枝晶臂間距的影響因素
  6. The moderate supersonic carbon added to the mold flux for ultra - low carbon steel is used to stay the melting speed as skeleton. then the mold flux coils have the good adiabatic, insulation and even flow property. at the same time it cause the carbon increase in the steel slabs and the operation of the ultra - low carbon is affected at last

    超低碳鋼連鑄結晶器用保護渣中，外加中超碳黑作為骨架降低熔化速度，使保護渣具有良好的絕熱保溫性、均勻流動的潤滑性，但同時卻會引起鋼鑄坯的碳增量，最終影響超低碳鋼的成功操作。
  7. Jiye pcd die blanks for drawing wire can always be trusted ; your dies always get excellent polishing quality, producing wire with flawless surface finish

    基業cd聚晶金剛石拉絲模坯擁有非常了的拋光質量，能確保拉線的表面光潔度。
  8. The online measurement of mold heat flux can not be replaced by online temperature measurement, the later can respond the uniformity of heat transfer and thickness of solidified shell mote accurately and directly, and online temperature and heat flux measurement of mold can be used to foresee the mold conditions such as fix and scaling of mold

    溫度的在線檢測不能代替熱流的在線檢測，後者可更準確和直接地反映結晶器傳熱和坯殼厚度的均勻性；同時在線檢測結晶器的溫度和熱流有可能對結晶器的設備狀態（如結晶器的安裝狀況和水垢狀況）實現在線預測。
  9. Numerical simulation on fluid field in mould for slab concasting

    板坯連鑄結晶器鋼液流場的數學模擬
  10. Finite element analysis of the flow field in the mould of slab conticaster

    板坯連鑄機結晶器內流場的有限元分析
  11. A study of water model on slag entrapment of molten steel in mould of slab continuous caster

    板坯連鑄機結晶器鋼液卷渣的水模型研究
  12. The effect of different operation parameters on the molten steel flow in the mould in no. 2 steelmaking plant, wisco has been studied via the three - dimensional flow field software developed by the authors

    利用開發的三維流場計算軟體，研究了操作參數對武鋼二煉鋼板坯連鑄機結晶器內鋼液流動的影響。
  13. Qualified molten steel from the steelmaking furnace will be contained in ladle and conveyed to continuous caster, poured into crastyllizer through pouring basket, then handled with the processes of vibration, water spraying cooling, straightening, roll conveying, flame cutting, and cooling on cooling bed, finally the formed billets will be stored at the stockyard or directly sent to the heating furnace of rolling mill for heating

    煉鋼爐冶煉出合格的鋼水，用鋼水包送至連鑄機，經中間包澆注到結晶器，再經振動水噴淋冷卻拉矯輥道輸送火焰切割冷床冷卻，最後存放于鋼坯堆放區或直接送至軋鋼機加熱爐進行加熱。
  14. Research on flow path of hot metal in beam blank mould

    異型坯連鑄結晶器內流場
  15. Curved mould copper tubes for bow - type continuous billet casting machine

    弧形方坯連鑄機結晶器銅管
  16. Numerical simulation on fluid flow in mould for slab continuous casting

    板坯連鑄結晶器內鋼液流動數值模擬
  17. Numerical value simulation of hot metal flowing in slab concaster mould

    板坯連鑄結晶器內鋼液流動數值模擬
  18. Numerical simulation of 3 - dimensional molten flow in thin - slab continuous casting mold

    薄板坯連鑄結晶器中鋼液三維流動的數值模擬
  19. The water modeling of fluid flow pattern in slab continuous caster mold at hangang

    邯鋼連鑄板坯結晶器內流場的水模擬研究
  20. Effect of multi - electromagnetic field on motion state at meniscus and quality of continuous casting metals

    復合電磁場對連鑄結晶器彎月面金屬液運動行為及鑄坯質量的影響
分享友人
分享到 Line

分享到臉書