模下壓板英文怎麼說

模下壓板 的英文翻譯

模下壓板 例句

1. Study on the characteristic of piezoceramic actuator is an important step in the studying of undamaged - inspection process based on piezoceramic actuator technology. this thesis firstly dwells on the sample model of piezoceramic actuator under the restriction of concrete. through theory and experimentation analysis, we arrives at a conclusion that the vibration behavior of piezoceramic actuator belongs to that of the thin plate
   本文著重研究了在混凝土約束條件 下 壓 電陶瓷片的樣本 模 型，在此基礎上通過理論探討和實驗現象分析，認為埋置於混凝土中的 壓 電陶瓷片是符合彈性力學中克希霍夫有關薄 板 理論的假設，是屬于薄 板 振動問題，並確定了其邊界約束條件。
2. Finally we focus our attention on studying the emission spectrum of two atoms driven by a single - mode field in an ideal cavity. we showed that the atomic emission spectrum is insensitive to the phase of field for the two atoms initially in the coherent superposition state tf / = v2 / 2 ( j +, - ) h ? + } ), when the two atoms is initially prepared in ( fs * } = cos ( 0 / 2 ] +, + ) + sm ( 0 / 2 ) ei ' p -, - ), the atomic emission spectrum is associated with not only the field photon - number distribution and the atomic populations, but also the phases of the field and the atomic dipole
   接著考察了好腔中由單 模 量子場驅動的雙原子發射譜，結果表明初態為的雙原子發射譜與驅動場的相位無關；而初態為的雙原子發射譜不僅與光場的光子數分佈以及原子的布居數有關，而且依賴于光場的相位以及原子偶極矩的相位，並且在適當的條件 下 ， 壓 縮真空場可將雙原子俘獲在相干疊加態。
3. Main product : tungsten carbide powder, roll ring, anvil and cylinder, mining button bit, dies nib for various application : cold heading dies, drawing dies and non - magnetic carbide dies. all of the products mentioned above could be offered in blank or finishing product
   公司主要產品有：碳化鎢粉硬質合金輥環頂錘和 壓 缸冷鐓 模 無磁合金礦山柱拉絲拉管 模 棒材 板 材非標 模 具及硬質合金精密加工產品等，廣泛應用於鋼鐵標準件金剛石粉末冶金石油礦山磁性材料機械加工電子等行業。
4. Toughening thermoset matrix composites with interlayered thermoplastic particles is an effective method to improve fracture toughness and impact resistance without sacrificing hot / wet properties. furthermore, transverse strength, fatigue resistance and solvent resistance can also be enhanced. drapability and tackness of interleaved prepreg is maintained as conventional level
   對樹脂基體復合材料採取層間顆粒增韌是提高復合材料層 壓 板 韌性、抗沖擊能力和抗分層能力的有效途徑，在保持原有復合材料濕熱性能的前提 下 ，通過層間顆粒增韌，還可以改善垂直纖維方向的強度、抗疲勞性能以及耐溶劑性，並不影響原有的成型工藝。
5. Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
   熱、 壓 環境 下 壓 阻變換 壓 力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8 模 型， 模 型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境 下 ，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高 模 型的適用性

模下壓板 的相似字

瀏覽更多漢英字典詞條

前往 漢英字典目錄 瀏覽全部詞條。