殘余應力測定 的英文怎麼說

中文拼音 [cányúyīnglìcèdìng]
殘余應力測定 英文
residual stress analysis
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 測定 : determine; determination; setting-out; admeasurement; assignment; assay; finding
  1. Standard test method for verifying the alignment of x - ray diffraction instrumentation for residual stress measurement

    殘余應力測量用x射線衍射儀校準檢定的測試方法
  2. The phase structure of different cu - fe thin films were studied by using grazing incidence x - ray analysis ( gixa ). the texture and residual stress of different cu - fe thin films were measured by scan of x - ray diffraction ( xrd ) and 2 scan with different. the thicknesses of different thin films were characterized by means of small angle x - ray scattering ( saxs ) technique. by using atomic force microscope ( afm ) measured surface roughness of thin films. the component of different thin film was characterized by energy disperse spectrum ( eds ) and x - ray fluorescence ( xrf ). the magnetic properties of cu - fe thin films were measured by means of vibrating sample magnetometer ( vsm ). in addition, the giant magnetoresistance ( gmr ) effects of different films were also measured. the original resistance of the film fabricated by a direction - current magnetron sputtering system is directly affected by bias voltage

    利用掠入射x射線分析（ gixa ）技術對不同cu - fe薄膜的相結構進行了研究;利用xrd掃描及不同角度的2掃描對薄膜進行了結晶織構及殘余應力分析;運用小角x射線散射（ saxs ）技術測量了薄膜的厚度;採用原子力顯微鏡（ afm ）觀察了薄膜的表面形貌;運用能量損失譜（ eds ）及x射線熒光光譜（ xrf ）對薄膜進行了成分標定;使用振動樣品磁強計測量了不同cu - fe過飽和固溶體薄膜的磁性能;最後利用自製的磁阻性能測試設備測量了真空磁場熱處理前後不同薄膜的巨磁阻值。
  3. The critical crack and stress put forward provides theoretic foundation for monitoring portal machine. 3. applying steady theory of board, studying the problem of early curvature, flexibility model, welding remaining stress, elastic transmutation and brace condition and so on, conclude that structure of beam is primary place where metal structure of portal crane lose stabilization and the break of main beam is result of losing partial stabilization of main board

    文章提出的界限應力和臨界裂紋對于港口機械的監測提供了理論依據； 3 、運用板的穩定理論，探索了作為薄壁構件的門機金屬結構在失穩破壞中所涉及到的初曲率問題、彈性模量問題、焊接殘余應力問題、彈塑性變形問題以及支承條件問題等，得出了門機金屬結構發生失穩破壞的主要部位為臂架結構，且主臂架的折斷是由於受壓翼板局部失穩引起整體破壞； 4 、探討了焊接對結構承載的影響。
  4. In the paper, the results of experience and rules of distribution of the cold - formed residual stress are analyzed, the models of the cold - formed residual stress that are close to the fact are founded, initial stress files of ansys which can describe the magnitude and distribution of the residual stress are established

    本文對冷彎殘余應力的實測結果和分佈規律進行了分析討論，建立了接近實際情況的槽鋼和卷邊角鋼的冷彎殘余應力模型，創建了能描述殘余應力分佈和大小的ansys初應力文件，並在ansys穩定分析中引入該文件，得到構件在殘余應力影響下的極限荷載。
  5. I wrought copper and copper alloys - detection of residual stress - mercury nitrate test

    鍛造銅和銅合金.殘余應力的測定.硝酸汞
  6. Copper and copper alloys - determination of residual stresses in the border area of a slit strip

    銅和銅合金.帶材寬面上殘余應力測定
  7. Copper and copper alloys - determination of residual stresses in the border area of slit strip

    銅和銅合金.切割鋼帶邊緣區域殘余應力的測定
  8. Blind hole method is a common method which is widely applied in the project to measuring residual stresses

    盲孔法是工程中被廣泛應用的測定殘余應力的方法之一，相移雲紋干涉方法可得到孔邊任意一點的位移信息。
  9. Standard test method for photoelastic determination of residual stress in a transparent glass matrix using a polarizing microscope and optical retardation compensation procedures

    用偏光顯微鏡和光學延遲補償方法在透明玻璃基質中測定光彈性殘余應力的標準試驗方法
  10. Non - destructive testing - standard test method for determining residual stresses by neutron diffraction iso ts 21432 : 2005 ; german version cen iso ts 21432 : 2005

    無損檢驗.用中子衍射測定殘余應力的標準試驗方法
  11. Standard test method for determining residual stresses by the hole - drilling strain - gage method

    用鉆孔應變儀法測定殘余應力的標準試驗方法
分享友人
分享到 Line

分享到臉書