法面齒距 的英文怎麼說

中文拼音 [fǎmiànchǐjù]
法面齒距 英文
normal circular pitch
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 距 : Ⅰ名詞1 （距離） distance 2 （雄雞、雉等的腿的後面突出像腳趾的部分） spur （of a cock etc ）Ⅱ動詞...
  1. The beyond is the simple notation of serial number of pricker, totaled 7 digits of codes, in which the first digit represents the diameter of needle - bar of pricker, the second digit represents the siding of triangle side on functional section of pricker, the third digit represent the length of functional section of pricker, whereas in standard notation, it represents the distance from needlepoint to gradual deflating small port ( lower port ), the fourth digit represents the total length of pricker, which is the distance from the inside of bending helve to the needlepoint, the fifth digit represents the total quantity of dents on the cording of functional section, and the sixth digit represents the model of barb on functional section, while the seventh digit represents the distance between barbs on functional section

    以上為刺針編號的簡單寫法，共7位代碼，第一位是刺針針桿的直徑；第二位是刺針工作段三角面的邊寬；第三位是刺針工作段的長度，同標準寫法所不一樣的是針尖到漸縮錐小口（下口）的距離；第四位是刺針的總長度，按彎柄內側至針尖的距離；第五位是工作段棱上的總齒數；第六位是工作段上鉤刺的型號；第七位是工作段上鉤刺與鉤刺之間的距離。
  2. By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given

    採用外點罰函數優化方法，通過取行星輪半徑和中心距之和作為優化目標函數，對滾錐齒超環面行星蝸桿傳動進行了參數優化，運用此優化程序，初步完成了對該種傳動的系列化研究，給出了傳動系列的最佳參數取值。
  3. The causes of formation of global form errors for sbg and its separation method are analyzed theoretically. the tooth surface deviation and pitch deviations resulted from tooth surface distortion are separated and derived

    從理論上分析了螺旋錐齒輪整體誤差的形成原因及其分離方法，根據整體誤差的性質，分離出由於齒面變形所引起的齒距誤差，獲得了齒面偏差。
  4. As the method of center distance varing was adopted and the technologe was differ from the condition of center distance constant, the gear concordance of abrasion rate on the tooth face of gears was improved obviously especially in the big gear

    由於採用了變更中心距的方法以及與定中心距的工藝不同，齒面研磨率的一致性得到明顯的改善，特別是大齒輪上更是如此。
分享友人
分享到 Line

分享到臉書