熔化潤滑 的英文怎麼說

中文拼音 [rónghuàrùngǔ]
熔化潤滑 英文
melt lubrication
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 潤 : Ⅰ形容詞（細膩光滑; 滋潤） moist; smooth; sleek Ⅱ動詞1 （加油或水 使不幹枯） moisten; lubricate 2 ...
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 熔化 : melt; smelt; meltdown; fusion; fusation; diatexis; eliquation; run; melting; smelting
  • 潤滑 : [機械工程] lubricating; lubrication; lubricate
  1. The moderate supersonic carbon added to the mold flux for ultra - low carbon steel is used to stay the melting speed as skeleton. then the mold flux coils have the good adiabatic, insulation and even flow property. at the same time it cause the carbon increase in the steel slabs and the operation of the ultra - low carbon is affected at last

    超低碳鋼連鑄結晶器用保護渣中，外加中超碳黑作為骨架降低熔化速度，使保護渣具有良好的絕熱保溫性、均勻流動的潤滑性，但同時卻會引起鋼鑄坯的碳增量，最終影響超低碳鋼的成功操作。
  2. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  3. Solder bar is made from high purity metal. by means of strict qualitg control the oxide and metallic and non - metallic impnrities and effectively minimized, the available high purity solder bar is with uniform and glazed surface good wetting and spreading ability after molten bright joint and minimum oxide residue after soldering. our product is suitable for wave and handwork soldering with high quality requirement

    本公司生產焊錫條採用高純度金屬原料，在嚴格品管條件下，有效控制氧化程度以及金屬和非金屬雜質含量，焊錫條表面均勻光滑，純度極高，熔化后流動性好，潤濕性極佳，焊點光亮，氧化渣物極少發生，適用於高品質要求的各種波峰焊和手工焊。
  4. Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward

    摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析，研究其運行不穩定的原因，提出改造措施，包括滑動軸承潤滑油槽，齒輪泵的機械密封，降低齒輪泵出口壓力，改自動提速為手動提速等等。
分享友人
分享到 Line

分享到臉書