皮厚因數 的英文怎麼說
中文拼音 [píhòuyīnshǔ]
皮厚因數
英文
skin-depth factor-
In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。Based nit the definition of production decline rate, the multifactor analytical model for composite decline rate is developed, which discusses affecting factors stub as the startup well number, water cut, producing fluid thickness, pressure, relative production index well spacing density, skin factor etc
摘要從產量遞減率定義出發，首先導出了綜合遞減率與開井數、含水、產液厚度、壓力、相對產液指數、井網密度、表皮系數等多因素分析模型。In upper level optimization, the thickness and geometry factors of composite skins and webs as well as other structural dimensions are taken as design variables. then, considering the behavior constraints and the side constraints, the structural mass is minimized by the mathematical programming technique. in lower level optimization, the mathematical programming technique or the genetic algorithm ( ga ) is used to search the practical stacking sequence of composite skins and webs to realize the given thickness and geometry factors from upper level optimization
底層優化設西北工業大學博士學位論文計以復合材料蒙皮和腹板等層合板各分層的厚度（或鋪層數） 、鋪層角和鋪層順序為設計變量，以層合板的幾何因子與頂層優化設計給出的最優幾何因子之間的誤差最小為目標，考慮層合板厚度和製造工藝性約束，採用數學規劃方法或遺傳演算法（ geneticalgorithm ，簡稱ga ）求出底層最優設計變量。分享友人