離軸誤差 的英文怎麼說

中文拼音 [lízhóuwùchā]
離軸誤差 英文
off axis error
  • 離 : Ⅰ動詞1 （離開） leave; part from; be away from; separate 2 （背離） go against 3 （缺少） dispens...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 誤 : Ⅰ名詞（錯誤） mistake; error Ⅱ動詞1 （弄錯） mistake; misunderstand 2 （耽誤） miss 3 （使受損害...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 誤差 : error
  1. Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error

    對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析，並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算，最後對誤差進行合成。
  2. The error induced will decrease as the pile spacing increase. the correlation of error and pile spacing is discussed in this paper

    以往通常將樁當作沒有粗細的直線段，這樣無疑會帶來一定的誤差，這種誤差將隨著與樁軸線距離的增大而逐漸減小。
  3. Influence of rotary errors of centrifuge spindle on accelerometer input accuracy

    精密離心機主軸回轉誤差對加速度計輸入精度的影響
  4. In this subject, a new method and technique that applied the error separation theory to test of the surface flaw of axis - like parts using eddy current is proposed for the first time. based on this method, a mathematical model of extracting the surface flaw of axis - like parts is established. then " an automation system for the eddy current examination of the surface flaw of axletree " is designed

    本課題首次應用誤差分離理論提出了對軸（孔）類工件表面缺陷進行渦流無損檢測的新方法和新技術，建立了基於該方法的提取軸（孔）類工件表面缺陷的數學模型，並設計了「軸承滾子表面缺陷渦流自動化檢測系統」 。
  5. Second, based on the theory of error separation, the mathematical model, which is used to extract the surface flaw of axis - like parts, is given briefly. third, the designs of hardware and software in the system are explained respectively. fourth, the models and algorithms for appraising the surface flaw of axis - like parts are established by the methods of pattern recognition and neural net

    第一，本文論述了該課題研究的必要性及應用開發的價值：第二，簡要介紹了基於誤差分離理論建立起來的提取軸（孔）類工件表面缺陷的數學模型；第三，對該系統的硬體和軟體設計分別進行說明；第四，運用模式識別和神經網路等方法建立軸承工件表面缺陷評判模型和演算法，並給出了各種評判方法的比較。
  6. Compared with the ordinary optimization algorithm of calibration, this algorithm is simple, less computational and high accuracy. finally, the paper put forward the ranging method based on similar triangle principle. it gives two ranging models according cooperation object vertical in the optical axis or not vertical in the optical axis and does experiment

    最後，本文提出了一種基於相似三角形原理的測距方法，根據合作目標與攝像機主光軸垂直與不垂直兩種情況，給出了兩種測距模型，建立實驗系統並進行了實驗，通過近距離段與遠距離段的測距結果與誤差分析驗證了此方法的有效性，能夠準確的確定合作目標的位置，計算簡單，測量精度高，具有重要的理論意義和工程使用價值。
  7. Further more, according to the characteristic of long - distance real - time broadcast and the redundancy of video signal, the paper establishes a difference arithmetic on the basis of frame transform and then analyses the error, gives a correspond physical model in order to satisfy the demand of long - distance control for over - axis signal

    並針對遠距離實時轉播的特點和視頻信號的冗餘性，在幀變換的基礎上引入了差值演算法，並進行了誤差分析，提出了相應的物理模型，以滿足對越軸畫面的遠程控制。
分享友人
分享到 Line

分享到臉書