wire shear 中文意思是什麼
wire shear
解釋
線材剪切機-
Abstract : the flying shear located behind the roughing stands of wire - rod mill is designed with hard surface gears for driving system, engaging of zero tolerance, hydraulic cylinder for clamping and shiftting, convenient and practical gap adjusting structure for blade
文摘:介紹了邯鋼三軋廠在線材軋機粗軋機組后的飛剪設計中，採用了硬齒面齒輪傳動，零側隙嚙合，液壓缸鎖緊與橫移及簡便實用的剪刃間隙調整機構。 -
On basis of the development of modern control technology and apply of the network technology and locale bus - mastering technology ， this text analyzes the essential element for produce of wire - roll mill : principle of assign for speed ; expatiates in detail on the network structure and communication protocol of ethernet and profibus - dp ; concretely describes the forms of control system configuration ， the function and features of its software and hardware designs ; also, introduces mainly control function of control system, ， for example ， sequence control 、 loop control 、 fly shear control and operation and monitor function etc
基於現代控制技術的發展、網路技術以及現場總線技術的應用，本文分析了線材生產的基本要素：速度的分配原則；分析了工業以太網ethernet和現場總線profibus - dp的結構和通訊協議。主要說明plc控制系統的組織結構形式，系統的軟硬體設計的功能和特點。同時，詳細介紹了控制系統的主要控制功能，如邏輯控制、活套控制、飛剪控制以及操作監控功能等等。 -
( 4 ) according to the principle of " repair as the old ", the schemes of foundation strengthening, the schemes of the body structure, the schemes of the shear wall strengthening, the schemes of the floor strengthening, the schemes of the brace layout, the schemes of the switch floor construction and special strengthening scheme such as carbon fiber, the wall steel wire grid strengthening are achieved in this paper
按照「修舊如舊」的原則實現了照舊色做舊，使新舊構件的色澤差別諧調。依據上述原則，論文實現了基礎加固施工方案，主體結構加固施工方案、剪力墻加固施工方案、樓板拆除支撐和砼施工方案、支撐布置方案、高層主體結構轉換層施工方案、木屋蓋拆除方案以及特殊加固工程施工技術如粘鋼加固、碳纖維布加固、墻面鋼絲網加固等。 -
The results of experiments shows that core column can increase flexural and shear resistant capacity and improve deformability and entirety of composite walls ; it is coordinate ductility of two composite walls joining wire or steels out - of - plane ; the seismic of composite walls joining with wire is fine than joining with steels ; the deformation of out - of - plane only affect the crack - loading, the ultimate carrying capacity and ductility in - plane nearly has no change
墻片試驗表明:芯柱可以增加復合墻體的抗彎和抗剪承載能力，改善墻體的變形能力和整體性;分別應用鋼絲網片和鋼筋連接的兩種復合墻體的平面外延性大致相同，內外葉墻協同工作良好;內外葉墻之間的連接提高了外葉墻砂漿層抗拉強度，同時也提高了復合墻體向外葉墻方向的抗推和抗拉承載力。 -
Shear test method for rivet wire and rivets
鋁及鋁合金鉚釘線與鉚釘剪切試驗方法 -
Aluminum and aluminum alloys - shear test method for rivet wire and rivets
鋁及鋁合金鉚釘線與鉚釘剪切試驗方法 -
Standard test method for shear testing of aluminum and aluminum - alloy rivets and cold - heading wire and rods
鋁和鋁合金鉚釘及冷鐓頭絲與棒材的剪切試驗的標準試驗方法 -
It is show that non - demoulding shear wall in which the cold - draw steel wire is taken as reinforcement has great capacity of resisting seismic and quality in the area of seismic
試驗及分析表明：免拆模板剪力墻墻片單元在墻片單元之中使用冷拔鋼絲網片作為配筋時具有良好的抗震性能，可以滿足地震區的設計要求。 -
Under different positions of a tripping wire or speeds of the side jet, the controlled experiments were made, including the receptivity of the shear layer near jet exit to acoustic excitations, the spatial development of fluctuating velocity and the profiles of mean velocity
在不同絆線位置或不同旁射流流速條件下，研究了射流出口臨近剪切層對聲激勵的感受性，脈動流速向下游的空間演化及平均流速剖面。 -
On the basis of stability analysis, the author takes the k27 + 825 slope from the type of slope which has lest stability as an example. according to its basic feature, the design ueses the choosed best reinforce and control scheme : lattice beam, anchor wire, grouting and abstraction of water. in the course of design, the author takes into account not only reasonable optimize of whole control plan but also local measure such as whether the unstable block will shear from vnlnerable sections when control plan is laid out concretely, in order to reach the goal of reasonable design and effective control
在穩定性分析的基礎上，以邊坡穩定性最差的一類中的k27 + 825邊坡為例，結合其自身的特點，用優選出的加固防治方案：框架梁+錨索斗灌漿+排水進行設計，設計中既考慮總體防治方案的合理優化，又充分考慮了加固工程的具體布置時是否存在不穩定體從錨索或框架梁的薄弱部位剪出的可能性等一些細部措施，以達到合理設計，有效及經濟治理的目的。
分享友人