濺射腐蝕 的英文怎麼說

中文拼音 [jiànshèfǔshí]
濺射腐蝕 英文
sputter etching
  • 濺 : 動詞（液體受沖擊向四外射出） splash; spatter
  • 射 : Ⅰ動詞1 （用推力或彈力送出） shoot; fire 2 （液體受到壓力迅速擠出） discharge in a jet 3 （放出） ...
  • 腐 : Ⅰ名詞（豆腐） bean curdⅡ動詞（腐爛; 變壞） decay Ⅲ形容詞（腐爛） rotten; corroded; putrid
  • 蝕 : Ⅰ動詞1. （損失; 虧耗） lose 2. （腐蝕） erode; corrode Ⅱ名詞（天體現象） eclipse
  • 腐蝕 : 1 （通過化學作用使物體逐漸消損破壞） corrode; corrosion; corroding; deep etch; diabrosis; rot; ea...
  1. Our experiments emphasized the correlation between micro structures and some properties of the coatings and tried to obtain the protective coatings with the comprehensively good properties, in which auger electron spectroscopy ( aes ), scanning electron microscope ( sem ), and x - ray diffraction ( xrd ) were employed to investigate the composition, microstructure and crystal phase of the coatings respectively, and the properties test was primarily considered with the wear resistance and corrosion resistance of the coatings

    本論文主要採用pvd技術中的磁控濺射鍍膜（ ms或rms ）及部分用等離子噴塗（ ps ）和熱氧化（ to ）表面處理技術研究了鈾的具有代表性的三種防腐保護鍍層，即單質al 、氧化物al _ 2o _ 3和合金al - zn鍍層。實驗力圖在制備技術、工藝參數及鍍層的微結構和性能之間找到一些內在的聯系，探索綜合性能較好的防腐蝕鍍層。
  2. For example, the silicon is etched anisotropically in the koh solution, the lucent al film is made with the magnetron sputtering system, the pressure hole is drilled by the supersonic stiletto machine and the silicon and the glass are bonded with electrostatic bonding setup

    例如， koh溶液對硅的各向異性腐蝕，磁控濺射臺製作光亮的鋁膜，超聲打孔機製作導壓孔，靜電鍵合裝置對硅島膜與玻璃極板的陽極封接等等。
  3. A special clamp for etching optical fiber and depositing pd film on the fiber is designed. designed a encapsulation set of the characteristics that is dampproof, shake and eroding resisted. the experimental set - up for hydrogen sensing includes the light source, gas cell, mass flow controller, stainless steel helical tubing and the detector, etc. the experimental results are also discussed

    本文還設計了一套光纖腐蝕用夾具、光纖封裝加熱夾具和一套光纖濺射鍍膜實驗夾具;設計並製作了一套具有防潮、抗震和抗腐蝕功效的光纖傳感頭封裝裝置;設計了一套由激光器、反應混合氣室、光功率計、質子流量計和流量控制器等組成的氫氣定標實驗裝置並對實驗數據進行了分析與處理。
  4. The work mainly consists of four parts : the first part is to use oxidation and lpcvd technique to produce sio2 mask film and si3n4 insulation film in order to enhance the heating efficiency of micro chamber, and guarantee the carry out of the reaction. the second part is to use the combination of dry etching and wet etching to produce reaction micro chamber, it is the container which carry out the pcr reaction, and dna sample carry out amplification reaction here. the third part is to use the sputtering, photolithography to produce heaters and temperature sensors which heat the reaction micro chamber and provide the temperature condition for the pcr reaction

    首先，利用氧化工藝和lpcvd技術，生長sio _ 2掩膜層和si _ 3n _ 4絕緣層，以提高反應腔的熱效率，保證擴增反應的順利進行；其次，用濕法腐蝕和干法刻蝕相結合的方法加工微型腔體，使之作為dna樣品進行pcr擴增反應的容器；第三，用濺射、光刻等工藝在微型腔體底部製作微型加熱器和溫度傳感器，實現對反應腔體的加熱及其溫度的精確測量，提供pcr擴增反應所需的溫度條件。
分享友人
分享到 Line

分享到臉書