燒結劑 的英文怎麼說
中文拼音 [shāojiējì]
燒結劑
英文
agglomerant-
The material was sintered at 1050 for three hours to get the porous artificial bone, that its apparent porosity was54 %, its volume density was 1. 28 g / cm3, and its bending strength was 13. 25mpa. the results showed that the sintering temperature was reduced by adding bioglass
本研究採用含生物玻璃前驅體粉末原料，添加檸檬酸造孔劑，模壓成型，在1050燒結保溫3小時，獲得了顯氣孔率為54 、體積密度為1 . 28s cm ~ 3 、抗彎強度為13 . 25mpa的多孔hap人工骨材料。The studies indicate that different content of pyrophyllite and dolomite can cause the following three cases : ( 1 ) making the refractory point decrease linearly and, to some extent, influencing the microstructure and properties of sintered body ; ( 2 ) acceleratingmullite formation during sintering, reducing thermal expansion coefficient of bond, reinforcing the matching nature and improving the flexural strength and shock strength ; ( 3 ) preventing sic grinding tool from generating black core, expanding suitable sintering temperature range of sic grinding tool
同時，也不同程度地影響了磨具燒結體的微觀結構和性能； （ 2 ）可促進在燒結過程中莫來石的形成，降低結合劑的熱膨脹系數，加強了結合劑與磨料的匹配性，提高了磨具的抗折強度和抗沖擊強度； （ 3 ）在一定溫度范圍內還可防止碳化硅磨具出現黑心現象，拓寬了碳化硅磨具的燒結溫度適應范圍。For the ceramic materials, the effects of additives such as pbo, b2o3, co2o3, mno2, cr2o3, sb2o3 on the electrical properties of bismuth - free zno - glass varistor were studied. the glass phase formed mainly by pbo and b2o3 during sintering process could decrease the sintering temperature, improve grain uniform growth and inhibit grain second growth. nonlinear property could be improved by properly adding co2o3, mno2, and cr2o3
對瓷料而言，系統研究了非bi系zno -玻璃料配方體系中pbo 、 b2o3 、 co2o3 、 mno2 、 cr2o3 、 sb2o3等添加劑對壓敏電阻電性能的影響規律，其中， pbo 、 b2o3在燒結過程中形成的玻璃相，可降低燒結溫度，促進晶粒均勻生長，抑制晶粒二次長大， co2o3 、 mno2 、 cr2o3做為非線性添加劑，適量添加可提高樣品的非線性， sb2o3做為改性添加劑，在燒結過程形成的尖晶石相可細化晶粒，抑制晶粒二次生長，改善樣品的綜合電性能。As showed by the results, mpf is advantageous for the stable formation or growth of pre - sintered glass beads, and it can partly guarantee the desired " results of sintering
研究結果表明，利用復配造孔劑有利於顆粒的穩定生成和成長，在一定程度上保證燒結過程達到理想狀態。Abstract : basic stuff of sinter flyash ceramisite is flyash and clay as agglomerant. the si nter flyash ceramisite is of dense in structure, low porosity which can improve t he mechanical properties of the material. it has properties such as high strong a nd low absorption of water and better stability. it is a new type ofbuliding mate rial
文摘:燒結型粉煤灰陶粒的主要原料是粉煤灰和作為粘結劑的粘土，文中所述燒結粉煤灰陶粒結構緻密，孔隙率低，能較好地改善了材料的力學性能，具有高強、吸水率低、穩定性好等特點，是一種新型建築材料The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites
研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。Made of polytetrafluoethylene resin added with a certain volume of colouring agent shaped as blank by moulding and sintering, then through cutting and rolling to have the stereospecific and non - stereospecific coloured film in 13 kinds of colour i. e. red, green, yellow, violet, brown, black, orange, white and etc
用聚四氟乙烯樹脂加入一定量的著色劑后經模壓，燒結製成坯料再經車削，壓延製成紅、綠、藍、黃、紫、棕、黑、橙、白等十三種顏色的聚四氟乙烯定向或不定向彩色薄膜。Dropping of mgo etc can decrease sintering temperature of al2o3 efficaciously, and make al2o3 sintered at 1450 c for 1 hour
Mgo等礦化劑的引入能夠有效的促進al _ 2o _ 3陶瓷的燒結，使其能夠在1450保溫1小時的條件下發生燒結。After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method
經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。Pore parameters ( porosity and distribution of pore diameter ) of porous glass prepared by filler principle were measured and analyzed. they were mainly determined by the volume ratio and the particle diameter of the pore former in the green body. preparation and sintering process of the samples resulted in the difference between the porosity and the volume ratio of the pore former. they were also responsible for the deviation between the distribution of poer diameter and the particle diameter of pore former
研究表明，利用填充法制備的多孔玻璃的孔參數（氣孔率、孔徑分佈）可進行設計與控制，多孔玻璃的氣孔率和孔徑分佈主要取決于成孔劑的體積比及其顆粒分佈，前者與後者之間的偏差取決于生坯制備及燒結過程。Rapid repairing mass for converter ismade of electro baked magnesite and high - quality synthetic sandand manufactured by adding high fluidity recarburizer ( beveloped by ourselves ) as addition agent withspecial technique. lt has the characteristics of well fluidity, well rapid fluidityand rpid sintering etc. it is applied to hot patching of large area before or after the converter as rapping hole patching and other parts for converter
轉爐快速補爐料是以電熔鎂砂和優質合成砂為主要原料，配以自行研製的高流動性的增碳劑為添加劑，以特殊工藝生產製成，具有流動性好、快速燒結等特點，適合於轉爐的前後大面的熱修補及出鋼口等部位的修補The ni - cu solid solution has the same function as ni and cu additives to promote the densification of w - mo - ti system composites
Ni - cu固溶體顯示出與ni 、 cu燒結劑同樣的活化燒結作用。The product is manufactured by taking high purity fused magnesia as raw material and adding a special binder, sintering agent and coagutant through a special production process
該產品是以優質高純電熔鎂砂為主要原料，外加特殊結合劑、燒結劑、促凝劑，經過特殊的生產工藝加工而成。Tundish coating is made from magnesia and magnesia - calcium materials. this kind of productions is densed after being shaked. there is no use for stoving. it ' s noted for low cost easy for using, no pollution and can be used for 20 ~ 60 hours
中間包乾式料振動是用鎂質和鎂鈣質材料、添加各種復合燒結劑製成的，經振動密實且無需烘烤即可使用的材料，其特點是現場操作簡單、能耗小、低成本、不污染環境、連澆爐數多，可使用20 ~ 60小時。Combining the characteristic of the fabrication of fgm by particle co - sedimentation, the densification of fgm has been designed from three aspects : the densification mechanism, the correlative parameters of the additives and the sintering schedule. subsequently, the densification of the w - mo - ti system composites has been investigated
結合共沉降法制備功能梯度材料的特點，從緻密化的機理選擇，燒結劑種類、含量和粒度的確定，燒結機制的確定等三個方面對其緻密化思路進行了設計，並對論文選用的w - mo - ti體系的復合材料的緻密化進行了初步研究。The layer spacing changes from 2. 2 nm to 3. 3 nm. tio2 is a functional materials with some outstanding physical and chemical properties which have many important application in areas including environmental purification, photocatalyst, and high effect solar cell
欽酸鉀是一種寬帶半導體材料，現在有過關于用燒結法合成欽酸鉀纖維，並用這些纖維作為復合材料增強劑的報道，但是這種纖維多是微米級的。Baseing on the request of low coercivity and high squareness in application, we had confirmed the main formulation of the lizn ferrite ; during the study of the conventional ceramic process, with the main formula foundation, we mainly studied the influence of ti4 +, co3 + on lowering coercivity and bi2o3, v2o5 on lowering sinter temperature. the results showed bi2o3 good characteristic on lowering sinter temperature and the sample which mixed with 1 % bi2o3 could reduce 40 % coercivity through slowing heating rate and extending the holding time
在氧化物陶瓷工藝技術研究中，按實際應用中低矯頑力、高矩形比的要求，確定了lizn鐵氧體的主配方，在主配方基礎上進行了ti4 + 、 co3 +等離子對降低矯頑力的研究以及添加bi2o3 、 v2o5助熔劑對降低燒結溫度的研究，發現bi2o3具有優良的降低燒結溫度的特性，在添加bi2o3樣品燒結過程中，降低升溫速率，延長保溫時間可以降低40 %左右的矯頑力。The injection process parameters influencing on injection, debinding behavior and process influencing on defects, sintering influencing on shrinkage, density, mechanical properties, and stainless steel adding cu for injection molding were examined. the experiment showed that flowing property of mixing was improved other than stability with increasing temperature and paraffin ratio in binder
用石蠟、聚乙烯、聚丙烯為添加劑，油酸為表面活性劑，組成石蠟基多組元粘結劑體系，研究注射成形工藝過程，工藝參數對成型的影響，脫脂行為和脫脂工藝對脫脂缺陷的影響，燒結工藝對收縮率、密度、力學性能的影響，以及含銅不銹鋼對不銹鋼耐蝕性的影響。Dry ramming material selects synthetic raw material and additive. it is noted for high density, easy for sintering and building, which is idel materials for hp, uhp electric stove
乾式搗打料是選用合成原料及添加劑製成的，具有抗鋼水滲透性強、易燒結、堆積密度高和施工方便等特點，是hp 、 uhp電爐爐底使用的理想材料。An agent or instrument used to destroy abnormal tissue by burning, searing, or scarring, including caustic substances, electric currents, lasers, and very hot or very cold instruments
燒灼劑通過燒、灼或結疤手段用於破壞不正常人體組織的藥劑或儀器，包括腐蝕物質、電流、激光以及極熱或極冷的儀器分享友人