面砂 的英文怎麼說

中文拼音 [miànshā]
面砂 英文
facing sand
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 砂 : 名詞（沙子） sand; grit
  1. After setting, the surfaces of the specimens are ground down using carborundum and alumina.

    凝固之後，樣品表面連續用金鋼砂或氧化鋁磨平。
  2. In the research area, the incised valley was formed during the sea level downwards and was provided source by the arenaceous river from qiaotou. it is stacked by 3 incised valleys formed in 3 different sequences

    研究區內子洲鎮川堡地區發育的下切河谷形成於海平面下降時期，來源於橋頭的砂質河流沉積，為疊置的、形成於三個不同三級層序底部的下切河谷充填沉積。
  3. A detailed introduction was made to the properties of the wet coated sand suitable for multi - station shell mould shooting machine ; the development of a sort of high strength coated sand with low resin content : the shaping index and wetness adjusting process : analysis and prevention of peel back defect of shells made with overturning hopper process ; test method of peel back resistance of coated sand : pinhole defect analysis of high ni ductile iron shell mould castings and application of anti - pinhole coated sand

    詳細介紹適用於吹砂式多工位殼型機的濕態覆膜砂性能；高強度低樹脂量覆膜砂的研製；濕態殼型覆膜砂的成形性指數與調濕工藝；翻鬥法制殼時的脫殼問題分析和解決辦法；覆膜砂脫殼性檢測方法；高鎳球鐵件殼型鑄造表面針孔原因分析與抗針孔覆膜砂的應用。
  4. Are molded twice based on ping, birchen, poplar and tung through kiln drying, cutting by saw, put together by machine, stiching surface, hot press, sanding light and so on

    是採用松木樺木楊木桐木為基材，經過烘乾鋸切機拼貼面熱壓砂光等多道工序兩次成型。
  5. The bonded warehouse is flooring with carborundum which is wearable, dustproof, and anti - statics

    倉庫地面採用耐磨金剛砂，耐磨、防塵、防靜電。
  6. The following examples of oil and gas fields in distributary and delta-fringe sand bodies range in age from late paleozoic to middle cenozoic.

    下面所列舉的是分佈於分流和三角洲前綠砂體的油氣田的例子，在地質時代上從晚古生代至中新生代。
  7. The only local coarse-grained sand-stones in the uppermost part are important for uranium.

    僅最上面局部的粗粒砂巖對鈾是有利的。
  8. According to the principle of surface and colloid chemistry, the pore structure and characteristics of tight sand gas reservoir are analyzed

    摘要根據表面與膠體化學原理，分析了低滲緻密砂巖氣藏的孔隙結構特徵、物性特徵以及它們之間的關系。
  9. German " butfering wide belt sanders ( double surface sanding ), the sanded block board has smoothly and even surface, and tiny thickness error

    沙光機：德國「比特飛靈「雙機組沙光機（雙面砂光） 、砂削后的細木工板表面平整，厚度誤差小。
  10. Special masonry mortar and plaster mortar for autoclaved aerated concrete

    蒸壓加氣混凝土用砌築砂漿與抹面砂漿
  11. This machine fits for mixing moulding sand in large scale and medium scale foundry workshop, as well as system sand for machine moulding, fired mold sand, self - hardening sand, face sand and core sand, also fit for mixing different powder materials for industries of glass, porcelain and fireproofing materials

    該機主要用於大中型鑄造車間型砂的混制，既可混制機器造型用的單一砂，又可混制干模砂自硬砂面砂和芯砂，也可用於玻璃陶瓷耐火材料等行業混制各種粉粒狀物料。
  12. The effective cost dust content of molding sand should be determined according to time factors such as the quality of the coal dust, casting size and thickness, pouring temperature, lacing sand or unit sand, and so on

    決定型砂中的有效煤粉含量應根據煤粉質量的優劣、鑄件大小和厚薄，澆注溫度、面砂或單一砂等因素。
  13. Wide belt sanders - test and inspection methods

    寬面砂帶拋光機.試驗和檢驗方法
  14. Management - flush the abrasion with water to get rid of the dirt and sand over the wound, then wash the wound with diluted disinfectant and then cover the wound with clean gauze

    處理方法當有輕微擦傷時，可用清水沖洗傷口表面砂粒或穢物，然後用稀釋的消毒藥水清洗傷口，再用清潔紗布敷裹患處。
  15. This series product fits for mixing facing sand and system sand in large scale or medium foundry workshop, as well as mixing core sand and self - hardening sand in large scale foundry workshop

    S11系列輾輪混砂機該系列產品主要用於大中型鑄造車間混制面砂和單一砂，也可用於大型鑄造車間混制芯砂和自硬砂等。
  16. The processing of surface : mirror sanding, titanic gold

    表面處理：鏡面、砂光、鈦金。
  17. During construction of inclined surface concrete for chamfer, it has always been a tough problem to reduce the occurrence of voids, pits and sand spots, etc. on the surface of concrete

    摘要在倒角斜面砼的施工中如何降低砼表面的蜂窩、麻面、砂斑、砂線一直是工程施工的一個難題。
  18. Standard test method for ultrasonic examination from bored surfaces of cylindrical forgings

    圓柱體鍛件表面砂心的超聲波測試的標準試驗方法
  19. To make graining aluminum alloys surface nowadays is mainly sand spraying. nevertheless, sand spraying requires many expensive and restricted facilities ; besides, it needs high working strength and is difficult for us to mass - produce. mass quality of sand spraying products is not conformed but with a high production cost

    現今鋁合金的表面砂紋處理主要是採用機械噴砂工序，但噴砂工序需要昂貴的專用設備，勞動強度高卻量產困難，批量品質難以一致，而且成本高，並受工件尺寸和幾何形狀的限制，對于薄鋁片噴砂后更有變形現象
  20. Test method for ultrasonic examination from bored surfaces of cylindrical forgings

    圓柱體鍛件表面砂心超聲波檢驗方法
分享友人
分享到 Line

分享到臉書