ferrule 中文意思是什麼
ferrule
解釋
n. 名詞 1. (裝于手杖、木柄、傘柄等頂端起加牢作用的)金屬箍,金屬包頭。2. 【機械工程】套圈,箍。
vt. 及物動詞 用箍鑲。
-
Measurement of connector ferrule hole inside diameter
連接器套管孔內直徑的測量 -
Steel tubes. straightening test on tubular half - ferrule
鋼管.反向壓扁試驗 -
Modification of zro2 optical fiber ferrule materials
2光纖套管材料的改性 -
Zirconia ferrule for connecting optical fiber
光纖連接器用氧化鋯陶瓷插針 -
Techincal requirement of ferrule for optical fiber connector
光纖活動連接器插針體技術要求 -
These mathematics models involved the theories includes : elastohydrodynamic lubrication theory, the bearing kinesiology and ferrule control theory, etc
這里所涉及到的理論有:軸承運動學,彈流潤滑理論,套圈控制理論等。 -
Measurement of connector ferrule inside and outside diameter circular runout
連接器套管內部和外部徑向跳動的測量 -
In regard to product technology, we have imported the eo rigid pipe ferrule technology and no - skive hose clamping technology so as to ensure the technical requirements of reliability and no leakage for the fluid circuit
在產品技術上我們引進eo硬管卡套技術和無需剝膠的軟管扣壓技術,確保液壓系統管路的可靠性、無泄漏的技術要求。 -
Note : 1 ) you must clean the ceramic ferrule and it ' s tip with alcohol and absorbent cotton very carefully before using
注意: 1 )使用前請將插針體和插針端面用酒精和脫脂棉清洗干凈。 -
Note : 1 ) you must clean the ceramic ferrule and it ' s tip with alcohol and absorbent cotton very carefully before using
注意: 1 )在使用前請將插針體和插針端面用酒精和脫脂棉清洗干凈。 -
Fitp219 multifiber ferrule endface geometry measurement
Fitp219多芯光纖套管端面的幾何尺寸測量 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - examinations and measurements - measurement of the angular misalignment between fibre and ferrule axes
光纖互連器件和無源元件.基本試驗和測量程序.檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 26 : examinations and measurements ; measurement of the angular misalignment between fibre and ferrule axes
光纖互連設備和無源元件.基本試驗和測量程序.第3 - 26部分:檢驗和測量.光纖和金屬加固環軸線間角度誤差的測量 -
Aerospace series - pipe coupling 8 30 in titanium alloy - nuts for welded ferrule ; german version en 4031 : 2001
航空航天系列.鈦合金管連接件8 30 ' .焊接金屬箍用螺 -
Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 33 : examinations and measurements - ferrule withdrawal force
光纖互聯裝置和無源部件.基本試驗和測量步驟.第3 - 33部分:金屬箍拔出力 -
Fibre optic interconnecting devices and passive components. basic test and measurement procedures. part 3 - 22 : examinations and measurements. ferrule compression force
光纖互連裝置和無源元件.基本試驗和測量程序.第3 - 22部分:檢驗和測量.金屬箍壓力 -
Fibre optic interconnecting devices and passive components. basic test and measurement procedures. part 3 - 23 : examination and measurements. fibre position relative to ferrule endface
光纖互連裝置和無源元件.基本試驗和測量程序.第2 - 23部分:檢驗和測量.與金屬箍端面相關的纖維位置 -
Running all ferrule fans, signal conrertor fans, hardpand ? driving fans, top cabinet, door ? fans, and checking whether they are normal or not
將各嵌套扇、信號變換器風扇、硬盤驅動器風扇、櫃頂、門風扇等電源接通,檢查各風扇,應運行正常。 -
Leave some of the tip on the ferrule to ensure you do not damage the ferrule
留一些皮頭在先角上以避免在後續操作的時候損傷先角。 -
The cue tip should be larger in diameter than the ferrule so that it can be properly shaped. make sure the glue is completely dry before shaping
粘合上的皮頭應該是比先角大上一圈的,待會我們會對它進行切割成型。在切割皮頭使其成型前要先確保膠水已經干透。
分享友人